Máy ép thổi khuôn

Hướng dẫn điều chỉnh áp suất thổi: Cài đặt tối ưu cho các loại vật liệu nhựa khác nhau

Mục lục

Tại sao áp suất thổi là một hệ thống, không phải một con số đơn lẻ

Aibim, a Wanplas factory based in Zhangjiagang, has manufactured injection (stretch) blow molding machines for more than 12 years, with 20 years of accumulated know-how in the injection blow molding field. Our lines serve customers in over 40 countries, run from our own CNC machining center, and produce more than 100 lines per year from a new factory established in 2022. Container sizes span from 3 ml medical droppers to 1000 ml cosmetic and food bottles. The single most misunderstood parameter among new operators is blow pressure. Many buyers ask for “the right blow pressure” as if it were one number printed on a dial. In reality, blow pressure is a system. It is the combination of a low-pressure preblow stage and a high-pressure final blow stage, multiplied by timing, material behavior, parison or preform temperature, mold temperature, and bottle geometry.

This guide explains blow pressure as a controllable process window rather than a fixed setpoint. We cover the physics of gas pressure pushing molten polymer against a cold mold cavity, the two-stage pressure architecture used on Aibim three-station one-step IBM machines, how pressure interacts with temperature and timing, and a full material-by-material table of optimal pressure windows. Whether you run PET, PP, PE, PS, SAN, PC, ABS, or TPU, the methodology below lets you move from a generic starting point to a verified, repeatable pressure recipe stored on the machine’s SD card.

Key Statistics
– Aibim: 12+ years of machine manufacturing, 20 years in injection blow molding know-how
– Exported to 40+ countries; 100+ lines per year capacity
– Container range 3 ml to 1000 ml; three-station one-step IBM process
– PREFILL hydraulic technology saves a minimum of 35% energy versus conventional hydraulic lines
– CE certified with light curtain and laser sensor safety systems

Vật lý của áp suất thổi trong tạo hình chai

Blow pressure exists for one physical purpose: to drive the molten polymer of the parison or preform outward until it contacts every surface of the blow mold cavity, then to hold it there while it freezes and takes the final shape. In injection blow molding the parison is injected as a tubular blank at the first station, transferred to the blow station, and expanded by compressed air. The air pressure does mechanical work against the polymer’s viscosity and against the heat-transfer rate of the mold wall.

When blow pressure is too low, the polymer cannot overcome its own viscosity and the mold’s cooling effect before it solidifies. The result is poor mold contact, shallow detail, thick-and-thin wall distribution, and weak structural zones. When blow pressure is too high, the polymer is forced into a thin, over-stretched skin that loses mechanical strength, develops internal stress, risks burst during the cycle, accelerates mold wear, and wastes compressed-air energy. The correct pressure is therefore a balance point where the material fully contacts the cavity with the minimum air energy required.

Air pressure also interacts with the rate of pressure rise. A steep, instant step from zero to maximum pressure can trap the material unevenly and create localized stress marks, while a controlled ramp that begins with a gentle preblow and rises to final blow gives the material time to distribute before it sets. This is why a two-stage system outperforms a single fixed pressure for bottles with non-uniform geometry.

The pressure required to move the polymer is a function of its extensional viscosity at the moment of blowing. A polymer that is still hot and soft extends at low pressure; the same polymer a few seconds later, after the mold has pulled heat from its surface, may need double the pressure to move the same distance and will instead tear or thin. This is the central reason blow pressure cannot be set without also controlling temperature and time. The operator is, in effect, racing the freeze front: pressure must arrive while the material is still mobile enough to flow, but not so early or so hard that it stretches the wrong zone.

Another physical factor is the surface area the air must push against. As the bubble grows, its internal volume rises with the cube of the radius while the wall area rises with the square, so the local stress in the wall drops as the bottle expands, provided the material keeps thinning evenly. If the pressure is too low, the bubble stalls before it reaches the cavity corners and the wall freezes in a thick, uneven state. If the pressure is too high, the bubble reaches the wall so fast that the material has no time to redistribute, producing a thin spot opposite the injection point and a thick ring near the neck. Reading the wall-thickness profile after a trial shot tells you far more about the correct pressure than the pressure gauge alone.

Hệ thống áp suất hai giai đoạn: Thổi sơ bộ và thổi cuối

Trên máy Aibim IBM, mạch khí nén được chia thành hai giai đoạn được kiểm soát. Hiểu vai trò của từng giai đoạn là nền tảng của việc hiệu chỉnh chính xác.

Áp suất thổi sơ bộ (giai đoạn áp suất thấp)

The preblow stage applies a low air pressure the moment the parison or preform enters the blow mold. Its job is to begin the expansion, establish the initial bubble shape, and guide where the material will go before the high pressure arrives. Preblow pressure and preblow timing together decide the wall-thickness distribution more than any other single variable. If the preblow is too weak or arrives too late, the material collapses onto the mold base before it has spread upward, leaving a thick bottom and a thin shoulder. If the preblow is too strong or arrives too early, the material stretches prematurely and thins in the zone that still needs material later.

Các cửa sổ thổi sơ bộ điển hình theo vật liệu được trình bày chi tiết trong bảng vật liệu dưới đây, nhưng về khái niệm, thổi sơ bộ cho các vật liệu định hướng như PET hoặc PCTG thường nằm trong khoảng 8 đến 16 bar, trong khi các vật liệu mềm như LDPE hoặc TPU nằm gần 4 đến 9 bar.

Áp suất thổi cuối (giai đoạn áp suất cao)

The final blow stage applies the high pressure that completes cavity contact, forms fine detail such as embossing or threads, and sets the bottle dimensions. Final blow pressure is held for a defined dwell, then vented. For PET the final blow commonly ranges 25 to 40 bar; for PP, PE, PS, and PC the windows differ and are listed per material. After the high-pressure dwell, a short exhaust and cooling phase lets the part solidify enough for transfer to the ejection station.

Sự khác biệt của thổi khuôn ép phun

In IBM the parison is injection-molded with precise wall distribution, then blown in a separate station on the same machine. Compared with extrusion blow molding, where the parison is extruded and hotter with more sag, IBM parisons are cooler and more controlled, so the blow pressure requirement is steadier and the scrap rate lower. Compared with two-step stretch blow molding of PET, IBM performs the blow on a preform that was just injected rather than re-heated, which removes the reheat oven variable but still requires correct blow pressure and timing for full orientation.

Áp suất thổi kết hợp với nhiệt độ, thời gian và khuôn như thế nào

Áp suất thổi không bao giờ được hiệu chỉnh riêng lẻ. Nó thuộc về bộ ba áp suất, nhiệt độ và thời gian. Thay đổi một yếu tố buộc phải thay đổi các yếu tố còn lại.

  • Liên kết nhiệt độ: Parison hoặc phôi ấm hơn chảy ở áp suất thấp hơn. Nếu bạn tăng nhiệt độ trục hoặc khuôn, bạn thường có thể hạ áp suất thổi mà vẫn đạt tiếp xúc đầy đủ. Sản phẩm lạnh hơn cần nhiều áp suất hơn, nhưng ép quá nhiều áp suất lên vật liệu lạnh tạo ra ứng suất và nguy cơ nổ.
  • Liên kết thời gian: Thời gian trễ của thổi sơ bộ và thời gian giữ của thổi cuối là các đòn bẩy thời gian. Thổi sơ bộ trễ làm vật liệu dịch chuyển xuống dưới; giữ thổi cuối lâu hơn cải thiện chi tiết nhưng kéo dài chu kỳ và tăng năng lượng tiêu thụ.
  • Liên kết nhiệt độ khuôn: Nhiệt độ khuôn kiểm soát tốc độ đông đặc. Khuôn lạnh cho phép bạn dùng áp suất cao hơn cho chi tiết sắc nét nhưng có nguy cơ ứng suất; khuôn ấm cho các vật liệu kết tinh như PP kiểm soát sự kết tinh nhưng cần áp suất được điều chỉnh để tránh hiện tượng chảy xệ.
  • Liên kết lực kẹp: Áp suất thổi tác động lên bề mặt bên trong khoang. Lực kẹp đầy đủ ngăn ngừa ba via tại đường phân khuôn. Tăng áp suất thổi mà không đủ lực kẹp sẽ tạo ra ba via thay vì chai tốt hơn.

Quy tắc thực tế: cài đặt cửa sổ nhiệt độ trước, sau đó thổi sơ bộ để thiết lập sự phân bố, rồi thổi cuối để tiếp xúc, cuối cùng tinh chỉnh thời gian. Không bao giờ khắc phục khuyết tật bằng cách chỉ thay đổi giá trị áp suất trong khi bỏ qua nhiệt độ và thời gian.

Thiết kế thành phôi chai và ảnh hưởng của nó đến áp suất thổi

In injection blow molding the parison is not a neutral tube; its wall thickness profile is set at the injection station and directly determines how much blow pressure is needed and where. A parison with a heavier base and lighter shoulder will need less final blow pressure at the bottom and more at the top. A parison with uniform wall needs a more uniform pressure ramp. Because the parison wall is programmable through the injection and core-rod design, the blow pressure window is really the second half of a two-part control system: injection sets the material budget, blow pressure spends it.

This coupling means a pressure problem is sometimes solved at the injection end rather than the blow end. If a bottle consistently shows a thin shoulder regardless of final blow pressure, the parison is likely too light at the shoulder and no amount of air will move material that is not there. Adding parison weight at that zone, or shifting the core-rod program, reduces the required blow pressure and improves the result. Conversely, an over-heavy parison forces you to raise pressure merely to spread excess material, which wastes energy and stresses the mold. Treating parison design and blow pressure as one loop is the fastest route to a stable recipe.

Tương tác thanh kéo giãn

On machines that include a stretch step, the stretch rod physically lengthens the preform before the air arrives. The rod sets the axial orientation; the blow pressure sets the radial orientation. If the rod moves too far before the preblow, the material is already thin axially and the final blow will over-thin the side wall. If the rod moves too late, the preblow alone must do the axial work and will need a higher pressure than the material tolerates. The pressure recipe therefore includes the stretch rod speed and start point as hidden variables, especially for PET and PCTG where biaxial orientation defines quality.

Cài đặt áp suất thổi tối ưu theo vật liệu

The table below gives engineering windows for each material processed on Aibim IBM machines. These are typical starting ranges, not guaranteed setpoints; always verify on the actual mold and material grade, and store the confirmed recipe on the SD card. Process temperature is the melt temperature in the barrel; mold temperature is the blow cavity temperature; hold time is the final-blow dwell.

Read the table as a band, not a point. Within each band, the correct value depends on wall thickness, bottle size, and cavity count. A thicker-wall bottle sits at the lower edge of the final-blow band because the material has more mass to push but less distance to travel; a thin-wall large bottle sits higher because the air must drive a light shell fully into a large cavity before it freezes. When moving between grades of the same polymer, raise the pressure slightly for higher molecular weight or higher filler content, and lower it for easier-flow grades. The per-material notes that follow explain the behavior behind each band so you can reason about adjustments instead of guessing.

Material Process Temp (°C) Preblow (bar) Final Blow (bar) Hold Time (s) Mold Temp (°C) Typical Defect Linkage
PET 260–285 8–16 25–40 1.5–3.0 10–25 Low orientation if preblow weak; haze if over-pressured
PCTG 255–280 8–15 24–38 2.0–3.5 20–40 Stress marks if cooled too fast
PP (clarified) 220–260 6–12 20–34 2.0–4.0 20–60 White stress marks if pressure ramps too fast
HDPE 200–230 5–10 16–30 2.0–4.0 10–40 Softness; needs good cooling before eject
LDPE / LLDPE 180–220 4–9 14–26 2.0–4.0 10–40 Low rebound; risk of sticking
PS 200–240 6–12 18–30 1.5–3.0 20–50 Brittle; bursts if final blow too high
SAN 210–250 7–13 20–32 2.0–3.5 40–70 Needs warm mold for gloss; sensitive to over-pressure
PC 280–320 10–18 30–45 3.0–6.0 80–120 High dry requirement; stress cracks if over-pressured
ABS 210–250 7–13 22–36 2.5–4.5 50–80 Opaque; tolerant, medium pressure
TPU 190–230 4–9 14–26 3.0–6.0 20–60 Soft elastic; sticking and rebound control needed

PET và PCTG

PET and PCTG are orientation-sensitive. PET must be dried below about 50 ppm moisture before processing, and the preblow establishes the biaxial orientation that gives the bottle its strength and clarity. A weak preblow leaves the material un-oriented and cloudy; a correct preblow followed by a 25–40 bar final blow gives a clear, strong bottle. PCTG is less moisture-sensitive than PET but still benefits from a controlled ramp; over-pressure on a fast-cooling cavity produces stress whitening rather than crisp detail.

PP

PP is crystallizable and temperature-sensitive. Clarified PP for transparent bottles needs a warm enough mold to control crystallization, yet too warm a mold causes sag that must be countered by adjusting pressure timing rather than by raising pressure blindly. A gentle pressure ramp reduces the white stress marks common in PP. The window of 6–12 bar preblow and 20–34 bar final blow suits most PP bottles.

PE (HDPE, LDPE, LLDPE)

Polyethylene is soft and has low rebound, so it needs relatively low blow pressure. HDPE suits 16–30 bar final blow; LDPE and LLDPE need even less because they are more flexible and tend to stick to the cavity. Cooling and demolding control matter more than raw pressure for PE. Over-pressuring PE wastes air and can flash at the parting line without improving the bottle.

PS và SAN

PS is intrinsically transparent but brittle. Final blow above the material’s comfort band causes burst or micro-cracks. A gentle, well-timed pressure rise is essential. SAN is similar but more chemical-resistant and glossy; it wants a warmer mold (40–70 °C) for surface gloss and a moderate pressure that does not over-stress the part.

PC

PC has high viscosity and demands high drying (below about 50 ppm) plus high process temperature (280–320 °C) and a warm mold (80–120 °C) to avoid stress. Blow pressure is among the highest of the common materials, 30–45 bar final, but the pressure must rise smoothly to avoid internal stress cracking. PC bottles are usually for medical or reusable drinkware where dimensional stability is critical.

ABS

ABS không trong suốt, bền và dễ gia công. Áp suất trung bình (thổi cuối 22–36 bar) là đủ. Nó được chọn cho hũ mỹ phẩm và chăm sóc cá nhân nơi màu sắc và bề mặt hoàn thiện quan trọng hơn độ trong suốt. Không cần sấy đặc biệt ngoài sấy thông thường, và khuôn có thể chạy ấm để có bề mặt tốt.

TPU

TPU mềm và đàn hồi. Nó cần áp suất thấp (thổi cuối 14–26 bar) và tháo khuôn cẩn thận vì bộ nhớ đàn hồi có thể gây dính và bật lại. Giữ và làm nguội lâu hơn trước khi đẩy sản phẩm giảm biến dạng. Chai TPU xuất hiện trong các ứng dụng y tế đặc biệt và mỹ phẩm cảm giác mềm mại.

Hiệu chỉnh áp suất theo hình dạng chai và độ dày thành

Một công thức áp suất hoạt động tốt cho chai tròn 100 ml có thể thất bại với chai không đối xứng 750 ml có tay cầm. Bảng dưới đây đưa ra các quy tắc hiệu chỉnh mà bạn áp dụng trên nền tảng cửa sổ vật liệu cơ bản.

Bottle Type Preblow Correction Final Blow Correction Timing Note
Thin wall (≤ 0.4 mm) Slightly higher to avoid early contact High, for full cavity contact Shorten high-pressure dwell to limit thinning
Thick wall (≥ 1.2 mm) Lower and later Extend dwell and hold Longer hold for complete freeze
Large volume (> 500 ml) Lower, delayed preblow Extend final dwell Manage cooling, watch cycle time
Small volume (< 50 ml) Higher preblow Moderate final Fast cycle, short dwell
Handle or asymmetric Zone-balanced Higher at fill stage for handle Delay to fill recessed zones
Wide mouth Lower preblow Moderate final Watch neck finish
Narrow neck Moderate Ensure base fills first Confirm base before neck pressure

Phương pháp tinh chỉnh áp suất từng bước

Sử dụng quy trình quyết định sau đây mỗi khi bắt đầu với vật liệu mới, khuôn mới hoặc kích thước chai mới. Quy trình giữ áp suất, nhiệt độ và thời gian theo đúng thứ tự.

>
Step Action Set / Adjust Verify
1 Fix material temperature window Barrel and mold temp per material table Melt flows, no degradation
2 Set preblow to form bubble Preblow bar and delay per material Even early expansion, no collapse
3 Set final blow for contact Final blow bar and ramp rate Full cavity contact, detail formed
4 Fine-tune timing Preblow delay, final dwell, exhaust Wall distribution balanced
5 Validate the part Measure wall, volume, burst, top load Within spec; no stress marks
6 Save and reuse Store recipe on SD card Same recipe runs on sister machines

Bắt đầu ở mức thấp của cửa sổ thổi cuối và chỉ tăng cho đến khi đạt tiếp xúc khuôn đầy đủ. Mỗi lần tăng trên mức tối thiểu là năng lượng khí nén bị lãng phí. Ghi lại các con số được chấp nhận để công thức có thể được nạp lại trên một máy IBM65 hoặc IBM75 khác mà không cần hiệu chỉnh lại từ đầu.

Khuyết tật liên quan đến áp suất: Bảng tra cứu nhanh triệu chứng và điều chỉnh

Bảng sau đây đối chiếu các khuyết tật thổi phổ biến với hướng điều chỉnh liên quan đến áp suất. Hãy coi đây là thẻ xử lý ban đầu; luôn xác nhận bằng các kiểm tra nhiệt độ và thời gian.

# Symptom Likely Pressure Cause Adjustment Direction
1Poor mold contact / incomplete formingFinal blow too low or delayedRaise final blow; check preblow timing
2Thin wall in shoulder or sidePreblow too early/strong, uneven parisonLower or delay preblow; adjust parison temp
3Thick wall / material pooling at basePreblow too late, final too lowAdvance preblow; raise final blow
4Bottle burst during cycleFinal blow too high or ramp too steepLower final blow; soften ramp
5White stress marks (PP/PE)Pressure ramp too fast, cold materialReduce pressure rate; raise temp
6Flash at parting lineFinal blow exceeds clamping forceLower final blow; verify clamping force
7Neck or finish deformationLocal over-pressure at neckReduce blow at neck; check mold temp
8Unstable base / rockingPreblow timing wrong, base not setAdjust preblow timing; lower final slightly
9Poor detail / embossing unclearFinal blow too low or dwell shortRaise final blow; extend dwell
10Internal stress cracking (PC/PS)Over-pressure, fast coolingLower pressure; raise mold temp; anneal
11Ovality / distortion after ejectPressure-cooling imbalanceBalance pressure with cooling time
12Weld line at handleInsufficient fill-stage pressureRaise final at handle stage; adjust parison
13Surface haze from over-pressureFinal blow too high for materialReduce final blow
14Short shot / incomplete fillAir volume or final blow insufficientRaise final blow; check air supply volume
15Pinch-off too thin / leakClamping and pressure mismatchVerify clamping; tune pressure
16Residual pressure trapExhaust timing too lateAdvance exhaust; check valve

Các sai lầm thường gặp khi cài đặt áp suất

Ngay cả những vận hành viên giàu kinh nghiệm cũng lặp lại một vài sai lầm mà phương pháp trên được thiết kế để ngăn ngừa. Nhận biết chúng giúp rút ngắn thời gian hiệu chỉnh.

  • Cài đặt áp suất trước nhiệt độ: Với nhiệt độ trục hoặc khuôn sai, mọi giá trị áp suất đều vô nghĩa. Hãy chỉnh nhiệt độ trước.
  • Khắc phục một khuyết tật bằng cách tăng áp suất: Vai chai mỏng hiếm khi được khắc phục bằng cách tăng áp suất thổi cuối; nó được khắc phục bằng trọng lượng parison hoặc thời gian thổi sơ bộ. Tăng áp suất chỉ làm vấn đề dịch chuyển sang nơi khác.
  • Dùng một công thức cho nhiều vật liệu: PET và PP không thể thay thế cho nhau; công thức phải thay đổi theo cấp độ nhựa.
  • Bỏ qua tốc độ tăng áp: Giá trị đỉnh ít quan trọng hơn tốc độ đạt được. Tăng áp nhẹ nhàng ngăn ngừa hiện tượng nổ và vết ứng suất.
  • Không lưu công thức: Một công thức đã kiểm chứng trên thẻ SD là kiến thức bị mất nếu không được lưu trữ và ghi nhãn theo vật liệu và loại chai.
  • Tăng áp quá mức để tạo biên an toàn: Biên áp suất 20% trên mức tối thiểu hiếm khi có ích và luôn lãng phí khí nén đồng thời làm mòn khuôn.

Hệ thống khí nén và hiệu quả năng lượng

Compressed air is one of the largest hidden costs in blow molding. Aibim machines use PREFILL technology and a variable displacement pump pressurizing system in the hydraulic circuit, and a staged high-low pressure air system for the blow function. The energy-saving design reduces consumption by a minimum of 35% compared with conventional hydraulic lines.

Air quality matters. For food, pharmaceutical, and cosmetic bottles the compressed air should be oil-free and dried to a clean class consistent with ISO 8573-1 concepts (oil, water, and particle limits). Contaminated air leaves odors or particles in the bottle and can foul valves. A staged supply separates the low-pressure preblow line from the high-pressure final-blow line so the compressor does not run everything at maximum pressure.

Air recovery, where practical, captures vented blow air or recovers expansion energy, lowering the effective energy per bottle. Even without full recovery, right-sizing the receiver, stabilizing line pressure, and only using the minimum final blow needed already cut air cost substantially. The table below compares energy and air indices using a baseline of 100 index points.

Configuration Air Energy Index Relative Cost vs Baseline
Conventional fixed pump, single pressure135High1.35× baseline
Staged high-low air, no recovery110Medium1.10× baseline
Aibim PREFILL + variable pump + staged air65Low0.65× baseline (35% saved)
Above with air recovery add-on52Low0.52× baseline

An toàn của hệ thống khí áp suất cao

Áp suất thổi cuối đạt 25–45 bar, và hệ thống khí nén tiềm ẩn nguy hiểm thực sự. Máy Aibim được chứng nhận CE và bao gồm rèm ánh sáng cho an toàn cá nhân và cảm biến laser kỹ thuật số tầm xa tại trạm tách sản phẩm cho an toàn khuôn. Các quy tắc an toàn cho mạch khí nén bao gồm:

  • Không bao giờ mở đường ống đang chịu áp; xả áp và khóa an toàn trước khi bảo trì.
  • Lắp và thử van xả áp trên bình chứa và mạch áp suất cao.
  • Bảo vệ trạm thổi khỏi các mảnh vỡ khi nổ; rèm ánh sáng sẽ dừng chu kỳ nếu tấm bảo vệ bị mở.
  • Kiểm tra ống, van và phụ kiện theo lịch trình; thay thế theo kế hoạch bảo trì.
  • Đào tạo người vận hành về dừng khẩn cấp và ý nghĩa của báo động áp suất.

Phương pháp xác minh chất lượng

Một công thức áp suất chỉ tốt khi có sự kiểm chứng đi kèm. Với mỗi công thức mới hoặc thay đổi vật liệu, hãy thực hiện các kiểm tra sau:

  • Độ dày thành theo từng vùng: Đo đáy, thân, vai và cổ bằng thiết bị đo độ dày; xác nhận sự phân bố khớp với thiết kế.
  • Dung tích: Đổ đầy để xác nhận chai đạt dung tích công bố.
  • Tải trọng đứng: Tác dụng tải trọng thẳng đứng để xác nhận độ bền xếp chồng.
  • Áp suất nổ: Tăng áp đến khi vỡ để xác nhận biên an toàn trên áp suất chiết rót.
  • Ngoại quan: Kiểm tra vết ứng suất, độ đục, ba via và độ rõ chi tiết.
  • Lấy mẫu sản phẩm đầu và mẫu theo lô: Kiểm định đầy đủ sản phẩm đầu tiên, sau đó lấy mẫu theo các khoảng thời gian cố định trong quá trình chạy.

Chi phí tương đối và cấu hình năng lượng

Chi phí vận hành cho một chai bị chi phối bởi vật liệu, năng lượng và phế phẩm. Bảng dưới đây xếp hạng các mức chi phí và năng lượng điển hình theo vật liệu trên các dây chuyền Aibim IBM. Xếp hạng sử dụng các mức Thấp, Trung bình, Cao, Rất cao và Cao cấp với các điểm chỉ số được tham chiếu đến mốc 100.

Material Material Cost Band Energy Index Air Cost Band Process Difficulty
HDPE / LDPELow90LowLow
PPLow95LowMedium
PSMedium100MediumMedium
ABSMedium105MediumLow
SANMedium108MediumMedium
PETMedium110MediumMedium
PCTGHigh112MediumHigh
TPUHigh115HighHigh
PCVery High130HighVery High

Chỉ số năng lượng được tính tương đối so với mốc 100 điểm cho chai PP tiêu chuẩn trên máy IBM65; PC cao hơn do nhu cầu sấy khô và khuôn ấm. Không con số nào trong số này là giá mua; chúng chỉ mô tả chi phí vận hành tương đối.

Máy ép phun thổi chai Aibim

Aibim chế tạo ba dòng IBM chính, mỗi dòng có hệ thống khí nén được kiểm soát cho thổi sơ bộ và thổi cuối. Các dải thông số dưới đây là các cửa sổ kỹ thuật điển hình; hãy xác nhận các con số chính xác theo bảng dữ liệu của nhà máy cho khuôn và vật liệu của bạn.

Máy ép phun thổi chai IBM75

Parameter Typical Range
ModelIBM75
Injection screw diameter (mm)45
Shot size (g)80–150
Clamping force (kN)750
Container volume (ml)50–1000
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–16 + 20–40
Installed power (kW)25–33
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)10–16

Máy ép phun thổi chai IBM65

Parameter Typical Range
ModelIBM65
Injection screw diameter (mm)40
Shot size (g)60–110
Clamping force (kN)650
Container volume (ml)10–500
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–16 + 20–40
Installed power (kW)18–25
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)9–14

Máy ép phun thổi chai IBM55 lai điện-thủy lực

Parameter Typical Range
ModelIBM55 Hybrid Electric
Injection screw diameter (mm)35
Shot size (g)40–80
Clamping force (kN)550
Container volume (ml)3–250
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–14 + 18–36
Installed power (kW)12–18 (hybrid, lower draw)
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)8–13

All three series share the PREFILL hydraulic technology and variable displacement pump pressurizing system, the SD card parameter storage for cross-machine recipe reuse, and the single-crossbeam double-pole clamping framework that enlarges mold setting space. The IBM55 hybrid adds electric servo motion for lower energy draw on small containers.

Các ngành ứng dụng và sự phù hợp vật liệu

Máy Aibim IBM phục vụ các ngành dược phẩm, thực phẩm, đồ uống và mỹ phẩm. Công thức áp suất phụ thuộc vào nội dung sản phẩm:

  • Dược phẩm: Chai đựng dung dịch uống, thuốc nhỏ mắt và chai chẩn đoán làm từ PE, PP, PS và PC cần các bộ phận sạch, không ứng suất; tăng áp nhẹ nhàng ở áp suất thấp bảo vệ bề mặt tiếp xúc với thuốc.
  • Thực phẩm: Chai đựng nước sốt, mật ong và gia vị làm từ PP và HDPE cần cổ chai chắc chắn; áp suất được điều chỉnh để đảm bảo độ kín.
  • Đồ uống: Chai nước và đồ uống chức năng bằng PET và PCTG cần định hướng phân tử để có độ trong và độ bền.
  • Mỹ phẩm: Hũ kem làm từ ABS và SAN, tuýp mềm làm từ TPU, và hũ trong suốt làm từ PET hoặc PCTG cần độ bóng bề mặt và chi tiết; áp suất được cài đặt cho chất lượng bề mặt hoàn thiện.

Các vật liệu có thể gia công trong dòng sản phẩm Aibim bao gồm PE (HDPE, LDPE, LLDPE), PP, PS, ABS, SAN, TPU, PC và PCTG.

Hướng dẫn lựa chọn: Từ yêu cầu đến model

Sử dụng bảng này để đối chiếu yêu cầu với cấu hình máy và khí nén. Các dải giá trị chỉ mang tính tham khảo; lựa chọn cuối cùng phụ thuộc vào số khoang khuôn và mục tiêu sản lượng.

Material Container Volume Wall / Output Recommended Model Air Config
PET / PCTG100–1000 mlMedium, high clarityIBM758–16 + 25–40 bar
PP / HDPE50–500 mlMedium, food gradeIBM656–12 + 20–34 bar
PS / SAN10–250 mlThin, glossyIBM55 Hybrid6–13 + 18–32 bar
PC50–500 mlThick, medicalIBM7510–18 + 30–45 bar
ABS10–500 mlMedium, opaqueIBM657–13 + 22–36 bar
TPU3–250 mlSoft, elasticIBM55 Hybrid4–9 + 14–26 bar
Small pharma3–100 mlHigh volumeIBM55 Hybrid6–14 + 18–36 bar

Dịch vụ và hỗ trợ

Aibim, as a Wanplas factory, applies the Wanplas group service commitments. Before shipment each machine is test-run and inspected with the customer, CE certified with light curtain and laser sensor safety. Our engineers perform on-site installation and commissioning, and train your operators on pressure tuning and recipe storage.

The Wanplas shared policy provides USD 500 free parts per year and free replacement of damaged parts within the warranty period. Because recipes are stored on an SD card, a verified pressure setting can be carried to a second machine, which makes process transfer and capacity expansion straightforward. We also offer remote operation support, open our factory for customer visits, and guarantee transportation, production capacity, and quality standards.

Câu hỏi thường gặp

Sự khác biệt giữa áp suất thổi sơ bộ và áp suất thổi cuối là gì?

Thổi sơ bộ là giai đoạn áp suất thấp bắt đầu sự giãn nở và thiết lập sự phân bố thành; thổi cuối là giai đoạn áp suất cao hoàn tất tiếp xúc khuôn và tạo hình chi tiết. Hiệu chỉnh thổi sơ bộ trước giúp kiểm soát độ dày, sau đó thổi cuối cố định hình dạng.

Vật liệu ảnh hưởng đến áp suất thổi trong ép phun thổi khuôn như thế nào?

Mỗi vật liệu có độ nhớt và tốc độ đông đặc khác nhau. PE mềm cần áp suất thấp; PC cứng cần áp suất cao và khuôn ấm; PS giòn cần tăng áp nhẹ nhàng. Bảng vật liệu trong hướng dẫn này đưa ra cửa sổ cho từng loại.

Tôi có thể dùng cùng áp suất thổi cho PET và PP không?

Không. PET cần thổi sơ bộ tạo định hướng phân tử và thổi cuối 25–40 bar, trong khi PP cần tăng áp nhẹ nhàng hơn và nhiệt độ khuôn kiểm soát sự kết tinh. Dùng công thức PET cho PP gây vết ứng suất; dùng công thức PP cho PET cho định hướng kém và mờ đục.

Tại sao chai của tôi bị nổ ngay cả ở áp suất vừa phải?

Hiện tượng nổ thường đến từ việc tăng áp quá dốc, vật liệu lạnh hoặc thành cục bộ mỏng do thời gian thổi sơ bộ sai. Hãy giảm áp suất thổi cuối hoặc làm mềm đường tăng áp, tăng nhẹ nhiệt độ và kiểm tra thời gian trễ thổi sơ bộ trước khi tăng áp suất.

Làm thế nào để tôi điều chỉnh áp suất thổi cho thiết kế chai mới?

Tuân theo phương pháp sáu bước: cài đặt nhiệt độ trước, cài đặt thổi sơ bộ cho hình dạng bong bóng, cài đặt thổi cuối cho tiếp xúc, tinh chỉnh thời gian, kiểm chứng độ dày thành và hiện tượng nổ, sau đó lưu vào thẻ SD. Bắt đầu ở mức thấp của cửa sổ thổi cuối và chỉ tăng cho đến khi tiếp xúc đầy đủ.

Áp suất thổi cao hơn có nghĩa là chất lượng chai tốt hơn không?

Không. Áp suất trên mức tối thiểu cần cho tiếp xúc chỉ lãng phí khí nén, tăng độ mòn khuôn và có thể gây ứng suất, nổ và mờ đục. Mục tiêu là áp suất thấp nhất cho tiếp xúc khuôn đầy đủ và đều.

Hệ thống khí nén của Aibim tiết kiệm năng lượng như thế nào?

Aibim sử dụng công nghệ PREFILL và bơm thể tích biến thiên trong mạch thủy lực cùng hệ thống khí cao-thấp phân tầng cho thổi. Sự kết hợp này cắt giảm năng lượng tiêu thụ tối thiểu 35% so với các dây chuyền thủy lực thông thường, và khí phân tầng tránh vận hành mọi thứ ở áp suất tối đa.

Chất lượng khí nén nào được yêu cầu cho thổi khuôn?

Đối với chai thực phẩm, dược phẩm và mỹ phẩm, khí nén phải không dầu và được sấy khô đến cấp sạch phù hợp với các khái niệm ISO 8573-1. Khí sạch bảo vệ an toàn sản phẩm và giữ cho van không bị tích tụ dầu gây ảnh hưởng đến sự ổn định áp suất.

Kết luận

Blow pressure is not one number but a two-stage system of preblow and final blow, shaped by material, temperature, timing, and bottle geometry. The material table, shape-correction rules, tuning flow, and defect card in this guide give you a repeatable method to find the minimum pressure that delivers full cavity contact and a sound bottle. Aibim, a Wanplas factory, builds IBM75, IBM65, and IBM55 Hybrid machines with PREFILL technology, staged air, and SD-card recipe storage that make this method easy to apply and transfer across lines.

If you are qualifying a new material or bottle, send us your material grade and bottle drawing. We will prepare a material-specific pressure process package and a machine configuration suggestion, and we welcome you to send samples for trial molding and to visit our factory for machine inspection and test runs. Our team will help you lock in a verified, energy-efficient pressure recipe before you scale production.