Hydraulic energy is one of the largest and most controllable cost lines in any blow molding plant, and for an injection blow molding machine the clamp and injection circuits run almost continuously across millions of annual cycles. PREFILL technology is Aibim’s answer to that load: a hydraulic architecture that pairs a prefill valve with a variable displacement pump pressurizing system so the machine only consumes the flow and pressure the current phase actually needs. Aibim, a Wanplas factory, applies this design across its IBM55 Hybrid, IBM65, and IBM75 machines and rates the result as a minimum 35 percent reduction in energy consumption versus conventional fixed-pump hydraulics. This article explains what PREFILL technology is, how it works step by step, the benefits it delivers, and how it is integrated into Aibim’s three-station injection blow molding machines for cosmetic, pharmaceutical, food, and drink packaging.
사출 블로우 성형기의 PREFILL 기술이란 무엇인가?
PREFILL technology is a hydraulic circuit strategy for injection blow molding machines that eliminates the standing energy loss of a conventional fixed-displacement pump. In plain terms, a standard IBM hydraulic power unit runs a pump at a set displacement and uses relief valves and proportional valves to dump or throttle the excess flow whenever the actuators need less than the pump can supply. That excess becomes heat, noise, and wasted electricity. PREFILL technology replaces this with two ideas working together: a prefill valve that rapidly fills the large clamp cylinder from the tank during low-pressure travel, and a variable displacement pump that pressurizes only to the level the process demands during injection and holding.
Aibim describes its system as a unique PREFILL technology combined with variable displacement pump pressurizing technology in the hydraulic system. The phrase “unique” signals that the implementation, valve sizing, and control logic are Aibim’s own engineering rather than a generic off-the-shelf power pack. Because Aibim runs its own CNC center for machine-part production, the manifolds and prefill components are made and matched to the machine, which supports both performance and serviceability.
PREFILL 기술은 유압 시스템을 일정한 전력 소비 장치에서 수요 기반 장치로 전환하며, 이것이 Aibim이 사출 블로우 성형 기계에서 최소 35%의 에너지 절감을 주장할 수 있는 이유입니다.
기존 IBM 유압 시스템의 작동 방식
To appreciate PREFILL technology, it helps to see what it replaces. A conventional injection blow molding machine typically uses a fixed-displacement pump driven by a constant-speed motor. The pump delivers a fixed flow whenever the motor runs. During a cycle the machine needs very different flows: a large volume to move the clamp platen quickly, a high pressure but modest flow to inject and hold the parison, and almost no flow during cooling and part handling.
고정 펌프 설계의 에너지 낭비
- 대기 손실. 액추에이터가 유휴 상태여도 모터와 펌프는 계속 회전하며 릴리프 밸브는 사용되지 않은 유량을 열로 변환하여 탱크로 되돌립니다.
- 스로틀링 손실. 비례 밸브가 수요에 맞춰 유량을 제한하며, 밸브 양단의 압력 강하는 열로 소산됩니다.
- 냉각 부하. 그 모든 열이 오일 온도를 높여 더 큰 쿨러, 더 많은 팬 전력, 더 빠른 오일 노화를 초래합니다.
- 소음과 마모. 연속 고압 바이패스는 생산 현장에서 부품 응력과 소음 출력을 증가시킵니다.
연간 수천만 사이클을 작동하는 기계에서 이러한 상시 손실은 미미하지 않습니다. 이는 생산되는 모든 튜브에 대한 구조적 세금이며, 더 큰 형체 실린더는 더 큰 고정 펌프가 필요하므로 기계 크기에 따라 증가합니다. 이것이 PREFILL 기술이 제거하도록 설계된 세금입니다.
PREFILL 기술의 작동 원리
The working principle of PREFILL technology can be understood as splitting the clamp motion into a low-pressure fast-fill phase and a high-pressure pressurize phase, then feeding each phase with the right device. The prefill valve handles bulk volume; the variable displacement pump handles pressure. The sequence below describes a typical clamp-close and inject cycle on an Aibim machine.
단계별 사이클
- 플래튼 전진(저압). 형체 실린더가 크기 때문에 플래튼을 빠르게 움직이려면 엄청난 펌프 유량이 필요합니다. 대신 프리필 밸브가 열리고 탱크의 오일이 큰 프리필 포트를 통해 실린더 보어로 급속히 유입되어 적은 펌프 노력으로 플래튼을 빠르게 전진시킵니다.
- 프리필 밸브 닫힘. 플래튼이 근접 스위치에 도달하면 프리필 밸브가 닫히고 실린더는 이제 펌프 라인만으로 공급되는 밀폐된 체적이 됩니다.
- 가압(가변 용량). 가변 용량 펌프는 클램프 톤수를 만들기 위해 변위를 잠시 팽창시킨 후 압력을 유지하기 위해 후퇴합니다. 변위가 가변적이기 때문에 고정된 유량이 아니라 상승하는 압력이 허용하는 유량만 공급합니다.
- 사출. 수요 기반 펌프에서도 공급되는 사출 회로는 코어 로드 주위로 용융물을 밀어 넥과 나사산이 있는 패리슨을 형성합니다. 압력은 버려지는 것이 아니라 설정된 프로파일로 유지됩니다.
- 보압 및 냉각. 보압 및 냉각 구간 동안 펌프 변위가 0에 가깝게 감소하여, 부품이 코어 로드에서 고화되는 동안 거의 전력을 소비하지 않습니다.
- 개방 및 인덱싱. 프리필 밸브가 다시 대용량 개방 스트로크를 관리하고, 인덱스 테이블이 코어 로드를 블로우 및 스트리퍼 스테이션으로 회전시키며, 동일한 수요 기반 로직이 적용됩니다.
핵심 통찰은 펌프가 완전 바이패스에서 릴리프 밸브와 싸우지 않는다는 것입니다. 변위가 부하를 추적하므로 소비되는 전력은 수행된 작업을 추적합니다. 이것이 PREFILL 기술이 단순히 손실을 재배치하는 것이 아니라 에너지를 절약하는 물리적 이유입니다.
가변 용량 펌프 및 가압
The variable displacement pump is the heart of the pressurizing side of PREFILL technology. Unlike a fixed pump that moves a constant volume per revolution, a variable displacement pump changes its geometric displacement in response to a pressure or flow command. When the system needs pressure but little flow, the swashplate (in a piston pump) or vane setting shifts to a small displacement; when it needs flow, displacement increases. A pressure-compensator loop caps the maximum pressure while letting displacement fall as pressure rises.
사출 블로우 성형에서 이것이 중요한 이유
- 덤핑 없는 압력 제어. 유지 압력은 릴리프 밸브를 통해 과잉 펌프 유량을 배출하는 것이 아니라 컴펜세이터에 의해 유지됩니다.
- 더 낮은 오일 온도. 스로틀링이 적을수록 오일에서 발생하는 열이 적어 냉각 수요와 오일 산화가 모두 감소합니다.
- 안정적인 사출. 펌프가 과잉 공급 대신 부하에 반응하므로 사출 속도와 보압이 설정 프로파일에 더 가깝게 유지되어, 소형 부품의 반복성을 돕습니다.
- 더 조용한 운전. 연속 바이패스 유량을 제거하면 생산 현장의 펌프 및 밸브 소음이 줄어듭니다.
Aibim’s “variable displacement pump pressurizing technology” is the pressurizing counterpart to the prefill valve. Together they form a closed, demand-matched hydraulic system rather than an open constant-supply system with throttle valves. On the IBM55 Hybrid, this hydraulic efficiency is layered with servo-electric motion on selected axes, pushing combined energy draw even lower while keeping the clamping rigidity that thin-wall precision requires.
PREFILL 기술의 핵심 이점
PREFILL 기술의 이점은 표면적인 에너지 수치를 넘어섭니다. 운영 비용, 부품 품질, 작업장 환경 및 장비 수명에 영향을 미칩니다. 표는 핵심 이점과 각각의 배후 메커니즘을 요약합니다.
| Benefit | Mechanism | Plant Impact |
|---|---|---|
| 에너지 절약 | Variable displacement tracks load, no full bypass | Minimum 35% lower electricity per machine |
| Lower oil temperature | Less throttling heat | Smaller cooler, slower oil aging |
| Stable process | Pressure matched to demand | Consistent neck and wall on small tubes |
| Faster low-pressure travel | Prefill valve bulk-fills clamp cylinder | Shorter clamp time, higher cycles |
| Quieter floor | No continuous relief bypass | Better working environment |
| Longer component life | Reduced heat and stress | Fewer seal and valve failures |
For cosmetic and pharmaceutical packers running several machines, the cumulative effect is significant. A 35 percent energy reduction on every machine, repeated across every shift, lowers the plant’s cost per thousand tubes and its carbon footprint at the same time. The Wanplas group, as the parent brand of Aibim, frames such efficiency as part of its broader value to global customers, alongside shared service promises such as spare-parts support and the open-factory policy.
에너지 소비 비교
이 콘텐츠의 비용 표에서 통화 수치가 제외되었으므로 아래 비교는 상대적 라벨만 사용합니다. 기존 고정 펌프 IBM 유압 시스템을 Aibim의 PREFILL 장착 시스템 및 올-일렉트릭 대안과 대조합니다.
| System Type | Relative Energy Use | Relative Investment | Best Fit |
|---|---|---|---|
| Conventional fixed-pump hydraulic IBM | High | Medium | Legacy lines, lowest upfront only |
| Aibim PREFILL hydraulic IBM | Low | Medium | High-volume precision small parts |
| Aibim IBM55 Hybrid (electric + PREFILL) | Very Low | Medium to High | Sustainability-target plants |
| All-electric IBM | Very Low | Premium | Maximum efficiency, higher budget |
The practical reading is that PREFILL hydraulics deliver most of the energy advantage of an all-electric machine at a more moderate investment, while keeping the clamping force and rigidity of hydraulics. For many injection blow molding applications, especially those needing strong clamp tonnage for multi-cavity molds, that balance is ideal. The IBM55 Hybrid pushes further by adding electric motion where it saves the most, so a buyer can choose the point on the curve that fits the budget and the sustainability goal.
사출 블로우 몰딩 품질에 미치는 영향
모든 유압 변경의 일반적인 우려는 에너지 절감이 공정 안정성을 희생하는지 여부입니다. PREFILL 기술에서는 그 반대가 사실입니다. 수요 매칭 펌프가 소형 부품 품질을 해치는 교란을 줄이기 때문입니다. 사출 블로우 성형에서 가장 중요한 두 가지 효과가 있습니다.
압력 변동 감소
In a fixed-pump system the relief valve and proportional valves introduce small pressure swings as they throttle. On a 3 ml to 15 ml mascara tube, where wall thickness may be a few tenths of a millimeter, those swings can show up as slight weight or gloss variation. The variable displacement pump holds the set pressure with less swing, so the parison weight and blow behavior repeat more tightly cycle to cycle.
더 차갑고 깨끗한 오일
Hydraulic oil that runs hot degrades faster and changes viscosity, which slowly shifts injection timing. By generating less heat, PREFILL technology keeps oil viscosity steadier across a shift and across seasons, reducing the need for constant parameter correction. Combined with Aibim’s SD card recipe storage, which reloads a proven parameter set on any machine, this makes multi-machine and multi-shift production far more consistent.
Aibim 기계의 PREFILL 통합
Aibim integrates PREFILL technology into its three-station, one-step injection blow molding platform. The range spans the IBM55 Hybrid, IBM65, and IBM75, covering a product range from 3 ml to 1000 ml and serving pharmaceutical, food, drink, and cosmetic customers in more than 40 countries. The PREFILL hydraulic system is one part of a broader machine design that also includes the following features.
- 단일 크로스빔, 이중 폴 클램핑 프레임워크. 금형 설치 공간을 확대하고 멀티 캐비티 툴링을 위한 안정적이고 견고한 클램핑을 지원합니다.
- CE 인증 안전. 스트리퍼 스테이션은 장거리 디지털 레이저 센서와 라이트 커튼을 사용하여 해당 영역이 비어 있을 때만 이젝션이 작동합니다.
- SD 카드 파라미터 저장. 작업자가 기계 간에 레시피를 저장하고 재로드하여 전환을 단축하고 검증된 공정 윈도우를 보호합니다.
- 하이브리드 옵션. IBM55 하이브리드는 PREFILL 유압 베이스에 서보 전기 동작을 추가하여 해당 범위에서 가장 낮은 결합 에너지 소비를 제공합니다.
- 자체 CNC 센터. Aibim은 유압 매니폴드를 포함한 자체 부품을 가공하여 독특한 PREFILL 구현과 더 빠른 서비스를 지원합니다.
Aibim은 Wanplas 공장이므로, 구매자는 PREFILL 유압 혁신뿐만 아니라 그룹의 공동 품질 기준, 예비 부품 지원 및 고객 방문을 환영하는 개방형 공장 정책도 얻을 수 있습니다.
유지보수 및 수명 고려 사항
PREFILL technology changes the maintenance profile of an injection blow molding machine in ways that usually reduce total cost. The biggest shift is hydraulic oil life. With less throttling heat, the oil oxidizes more slowly, so extended drain intervals are realistic under a normal filtration program. The cooler oil also reduces seal hardening and valve sticking, two classic sources of hydraulic downtime.
정기 관리 포인트
- 필터 모니터링. 흡입 필터와 압력 필터를 일정에 맞춰 관리하십시오. 프리필(prefill) 밸브와 가변 용량 펌프는 오염에 민감합니다.
- 프리필 밸브 점검. 계획 유지보수 중 프리필 밸브의 시팅과 파일럿 작동을 확인하여 고속 충전 단계가 정확하게 유지되도록 하십시오.
- 펌프 컴펜세이터 점검. 압력 컴펜세이터 설정이 공정 윈도우와 일치하는지 확인하고, 사이클 에너지나 속도가 변동하면 재교정하십시오.
- 오일 샘플링. 정기적인 오일 분석은 마모를 조기에 포착하고 PREFILL이 가능하게 하는 연장된 오일 교환 주기를 정당화합니다.
- 레시피 규율. SD 카드를 사용하여 검증된 파라미터를 고정하면 유압 시스템에 부담을 줄 수 있는 수동 재튜닝을 줄일 수 있습니다.
이 중 어느 것도 표준 유압 서비스 장비 이상의 특수 도구를 요구하지 않습니다. Aibim의 CE 인증, 잘 문서화된 설계와 Wanplas 그룹의 공유 서비스 약속은 수출 고객에게 예비 부품과 지원을 간단하게 만듭니다.
PREFILL IBM vs 기타 기계 유형
사출 블로우 성형 기계를 평가하는 구매자는 여러 기술 경로를 접하게 됩니다. 표는 소형 정밀 포장에 중요한 차원에서 Aibim의 PREFILL 유압 IBM을 주요 대안과 비교하여 위치시킵니다.
| Machine Type | 에너지 | Clamp Rigidity | Relative Cost | Note |
|---|---|---|---|---|
| Conventional hydraulic IBM | High | High | Medium | Proven but energy-heavy |
| Aibim PREFILL hydraulic IBM | Low | High | Medium | Best balance of force and efficiency |
| Aibim IBM55 Hybrid | Very Low | High | Medium to High | Electric motion plus PREFILL |
| All-electric IBM | Very Low | Medium to High | Premium | Highest efficiency, higher budget |
| Extrusion blow molding | Medium | N/A | Low | Lower neck precision |
Competitors in the broader IBM market include established builders such as Jomar in the United States, Bekum in Germany, and Milacron (Uniloy) with its blow molding systems, alongside high-volume electric press makers such as Haitian that influence hydraulic-versus-electric trade-offs. Aibim’s position is distinct: it keeps the hydraulic rigidity that multi-cavity precision tooling wants while removing the standing energy loss through PREFILL, offering a middle path that many cosmetic and pharmaceutical packers find optimal.
자주 묻는 질문(FAQ)
사출 블로우 성형기의 PREFILL 기술이란 무엇인가?
PREFILL technology is Aibim’s hydraulic design that combines a prefill valve with a variable displacement pump pressurizing system. The prefill valve lets the clamp cylinder fill rapidly from the tank during low-pressure travel, and the variable displacement pump only delivers the flow and pressure actually needed during injection and holding, instead of running a fixed pump at full output continuously.
PREFILL 기술은 에너지를 얼마나 절감하나요?
Aibim rates the PREFILL hydraulic system as saving a minimum of 35 percent of energy consumption compared with conventional fixed-pump hydraulic injection blow molding machines. The saving comes from eliminating the constant pressure-compensation flow and relief-valve throttling losses of a fixed pump.
어떤 Aibim 기계가 PREFILL 기술을 사용합니까?
PREFILL 유압은 IBM55 Hybrid 전기 기계, IBM65 및 IBM75를 포함한 전 제품군의 Aibim 사출 블로우 성형 설계의 일부입니다. IBM55 Hybrid는 PREFILL 회로와 서보 전기 모션을 결합하여 가장 낮은 복합 에너지 소비를 제공합니다.
PREFILL은 부품 품질이나 사이클 타임에 영향을 미치나요?
PREFILL improves quality consistency rather than harming it. By matching pump output to demand, it reduces hydraulic oil heating and pressure fluctuation, which stabilizes injection speed and hold pressure. The rapid prefill also shortens low-pressure clamp travel, supporting fast, repeatable cycles.
PREFILL은 전동(올 일렉트릭) 기계와 동일한가요?
No. All-electric machines replace hydraulics with servo motors and ball screws. PREFILL is a hydraulic optimization: it keeps the power density and rigidity of hydraulics but removes the standing energy loss of a fixed pump. The IBM55 Hybrid blends both ideas by using electric motion where it saves most and PREFILL hydraulics where clamping force is needed.
PREFILL은 어떤 정비 차이를 도입하나요?
Because the pump runs cooler and the relief valve throttles less, hydraulic oil degrades more slowly and cooling demand drops. Maintenance shifts toward normal filter and seal care plus the prefill valve inspection. Aibim’s SD card recipe storage also reduces setup-related wear by reloading proven parameters instead of manual re-tuning.
결론
PREFILL technology reframes the hydraulic system of an injection blow molding machine from a constant power consumer into a demand-driven one. By using a prefill valve for bulk clamp-cylinder filling and a variable displacement pump for pressurizing, Aibim removes the relief-valve throttling and standby losses that plague conventional fixed-pump designs, delivering a verified minimum 35 percent energy saving while improving process stability on small precision parts. Integrated across the IBM55 Hybrid, IBM65, and IBM75, and backed by Aibim’s single-crossbeam clamping, SD-card recipes, CE-certified safety, and the shared support of the Wanplas group, PREFILL technology gives cosmetic, pharmaceutical, food, and drink packers a compelling route to lower cost per tube and a smaller footprint without surrendering the clamp rigidity that multi-cavity tooling demands. For buyers comparing hydraulic, hybrid, and all-electric paths, Aibim’s PREFILL hydraulic IBM sits at the practical sweet spot of efficiency, force, and investment. Reach out to the Aibim team to size a PREFILL-equipped line for your volume and resin set.






