사출 블로우 몰딩 머신

프로스트(무광) 마감 병 생산: 사출 블로우 성형기 공정 설정

1. 병 무광(프로스티드) 마감의 4가지 방법

A frosted or matte surface on a plastic bottle is not a single technology but a family of approaches, each with a distinct cost profile, appearance consistency, and recyclability trade-off. For brand owners who specify injection blow molded (IBM) bottles, the most reliable route is to carve the texture directly into the blow mold cavity so that the parison replicates it during blow-up. Yet the market still uses at least three other routes, and a sourcing or product engineer should understand where each one wins and where it fails. This opening table is the backbone of the entire article because every downstream process decision flows from which frosting route you choose.

The first and most relevant route for this article is in-mold texture, also called mold cavity sandblasting or chemical etching. The bottle wall itself carries the frosted look; nothing is added or removed after molding. The second route is additive matting inside the resin: a nucleating agent in PP, a filler in PE, or a matting masterbatch in PS/SAN. The third route is secondary processing such as spray coating, acid etching, or mechanical sandblasting of the finished bottle. The fourth route is multi-layer co-injection or surface modification, where a thin matte skin is placed on a clear or colored substrate.

RouteHow the frost is createdAppearance consistencyRelative costCycle time impactRecyclability
In-mold texture (cavity sandblast / etch, VDI 3400 grade 21–45, SPI surface finish, etch depth a few μm)Parison touches a textured blow mold cavity and copies the micro-relief during blow-upExcellent, repeatable shot to shotMedium (one-time mold texturing cost, then free)Minor: needs slightly higher blow mold temperature and longer coolingBest, single-material, no additives or coatings
Additive matting (nucleating agent in PP, filler in PE, matting masterbatch in PS/SAN)Light scatters inside the bulk resin from dispersed particles or crystallinity changesGood, but batch-dependent and limited haze ceilingLow to Medium (continuous additive cost)Low, but may need longer cooling for high crystallinityGood, single polymer, though some masterbatches reduce clarity grade
Secondary processing (spray matte paint, acid etch, mechanical blast)Frost applied to the finished bottle off-lineMedium, depends on operator and line stabilityHigh to Very High (extra line, labor, scrap)Large, adds off-line steps and dryingPoor, coating or mixed surface defeats mono-material recycling
Multi-layer co-injection / surface modificationA thin matte skin layer over a clear or colored coreGood to excellentPremium (multi-barrel machine or co-extrusion)Moderate to large, layer balance adds complexityMedium, multi-layer but same-family polymer is acceptable

The table already tells the central story. For an IBM line that must hold a consistent frosted look across millions of bottles, in-mold texture is the only route that combines single-material recyclability with zero recurring consumable cost. Additive matting is cheaper to start and works well when a soft haze is enough rather than a true sand-blasted grip. Secondary processing is the most flexible for prototype runs but the least sustainable and the most expensive at volume. Multi-layer co-injection is a specialist answer for premium dual-tone bottles.

This article focuses on the in-mold texture route executed on an injection blow molding machine, because that is where Aibim, a Wanplas factory, delivers the deepest value: the machine, the mold, the cavity etching, and the process recipe that reproduces the frost shot after shot. Everything below explains how to set that process so the frosted finish is uniform, the cycle stays competitive, and the scrap rate stays low.

2. IBM 및 ISBM 공정 체인과 금형 질감의 역할

Injection blow molding is a one-step, multi-station process that converts plastic pellets into a finished bottle without a separate reheat stage. Understanding where the frosted texture is formed is the single most important concept before any parameter is set. The frost lives on the blow mold cavity, not on the injection mold that forms the parison.

2.1 3스테이션 및 4스테이션 IBM 터렛

A standard IBM machine runs a rotating turret through stations. The classic layout is three stations: 사출 (melt is injected around a core rod to form the parison), blow (the parison on the core rod transfers to the blow station, the blow mold closes, and compressed air expands the hot parison against the textured cavity), and strip (the finished bottle is ejected from the core rod). Some machines add a fourth conditioning station between injection and blow where the parison wall temperature is equalized before blow-up, which is valuable for frosted finishes because uniform wall temperature protects texture fidelity.

The sequence is continuous: while one core rod is being injected, another is being blown, and a third is being stripped. This is why IBM is called a one-step process. The bottle neck threads, the parison, and the blown body are all made in a single machine cycle, and the neck finish is molded to final dimension with no flash and no post-trim.

2.2 텍스처가 복사되는 위치

The parison is injected as a smooth-surfaced tube on the core rod. It has no frost. When the turret indexes to the blow station, the parison is clamped inside the blow mold whose cavity walls carry the sandblasted or chemically etched relief. Compressed air pushes the parison outward until it conforms to the cavity, and in doing so the parison skin takes a negative impression of the micro-texture. Because the parison is still soft and tacky at blow temperature, it copies the relief faithfully. That is the key reason the texture belongs on the blow mold, never on the injection mold: the injection mold only shapes the parison exterior, which is then stretched and pressed into the blow cavity where the visible bottle surface is born.

2.3 IBM 대 ISBM 원스텝 차이

Injection stretch blow molding (ISBM) also runs one-step on some machines, but it adds a stretch rod that pulls the parison biaxially before or during blow. ISBM is the standard for PET and for materials where molecular orientation improves barrier and top-load. For frosted bottles, the difference matters in two ways. First, ISBM typically runs a higher stretch ratio, which thins and elongates the parison skin; a deep frost texture can be partially ironed out by high stretch, so ISBM frosted bottles need a slightly coarser cavity grade and a stretch ratio tuned to preserve texture. Second, IBM keeps the parison wall thicker and the blow ratio lower, so the texture transfers with less distortion, which is why IBM is the preferred platform for precision frosted cosmetic and pharmaceutical bottles. Aibim machines cover both IBM and ISBM within the same turret family, letting a buyer choose orientation only where the material demands it.

실용적 핵심: 블로우 금형 캐비티를 텍스처 캐리어로 선택하고, 재료와 배리어 요구에 따라 IBM 대 ISBM을 결정하며, 전송 시 파리슨 온도를 프로스트가 선명하게 보일지 흐릿하게 보일지 결정하는 변수로 취급하십시오.

3. 무광 병용 재료 호환성

Not every resin freezes a frosted texture with the same clarity contrast. The table below maps the common IBM materials to their melt and mold temperature windows, the haze and gloss ranges you can expect, and a frosted suitability grade. These numbers are typical engineering ranges; validate against the resin data sheet for the exact grade you run.

MaterialMelt temperature (°C)Blow mold temp (°C)Haze range (%)Gloss 60° rangeFrosted suitabilityNotes
PP homopolymer / random copolymer, MFR 10–30 g/10min190–23025–45Controllable 15–6020–55BestMost controllable frost, low haze base, wide etch tolerance
PE HDPE / LDPE / LLDPE160–22015–35Natural 20–5015–40Low to MediumAlready semi-opaque; added frost contrast is weak
PS / SAN200–24030–55High contrast 5–4010–45HighClear base gives strong matte contrast; brittle, watch impact
PET (ISBM)260–290Optional warmed 60–110Medium contrast20–50MediumNeeds high stretch ratio with frost; texture can be ironed
PETG220–25020–40Soft 10–4525–55Medium-HighSoft, pleasant frost; low heat deflection limits hot fill
PCTG230–26025–45Soft 10–4525–55Medium-HighTougher than PETG, good for cosmetic droppers
PC / acrylic blend280–32060–110Medium30–60MediumHigh heat and clarity; premium cost
ABS / TPU200–25030–60Medium20–55MediumSpecialty look; TPU for soft-touch squeeze bottles

PP is the workhorse of frosted bottles. Its naturally low haze lets the etched relief read as a clean, even matte, and its broad melt window tolerates the slightly higher blow mold temperature that texture transfer demands. Random copolymer PP gives lower neck crystallization and fewer stress whiten marks around the finish, which is why many cosmetic lotion bottles pick it. PS and SAN deliver the strongest contrast because the clear base makes the matte pop, but their brittleness means drop performance and thread torque must be engineered carefully; SAN also resists many cosmetic oils better than PS.

PE is the least rewarding for a true frost because it is already translucent and its surface tends to look waxy rather than sand-blasted. PET and PETG work in ISBM when the stretch ratio is set to preserve the relief, and PETG/PCTG give a soft, premium satin that suits high-end droppers and jars. PC and acrylic blends are premium choices where heat resistance or optical depth is required.

4. 무광 마감용 공정 파라미터 설정(코어)

This is the heart of the article. A frosted finish is won or lost in the process window, and the parameters below are the ones an Aibim process engineer tunes on every texture trial. Read them as a connected system: the parison must be injected clean, conditioned even, blown with the right pressure profile, and cooled against a warm enough cavity to lock the texture.

4.1 사출(패리슨) 스테이션 설정

패리슨은 치밀하고 제팅 라인이 없으며 치수 안정적이어야 블로우 캐비티에 깨끗하게 안착됩니다. 주요 설정:

ParameterPP typicalPS typicalWhy it matters for frost
Barrel zone 1 (feed)190–200 °C200–210 °CStable feeding, no premature melt
Barrel zone 2 (compression)205–215 °C215–225 °CUniform plasticizing
Barrel zone 3 (metering)215–225 °C225–235 °CConsistent melt viscosity
Nozzle / adaptor220–230 °C230–240 °CPrevent freeze-off at gate
Injection pressure90–140 MPa100–150 MPaFill thin parison without hesitation
Holding pressure (profile)60–90 MPa70–100 MPaCompensate shrinkage, avoid sink at neck
Injection speedSlow–fast–slowSlow–fast–slowAvoid jetting marks that show through frost
Back pressure3–8 bar3–8 barHomogenize melt, remove trapped gas
Screw rotation speed60–120 rpm50–100 rpmMatch plasticizing to cycle
Core rod (mandrel) temperature60–100 °C70–100 °CControls parison skin set and transfer
Injection mold (parison) temperature15–35 °C20–40 °CCool parison enough to strip, not so cold it stresses

The slow–fast–slow injection speed is not optional for frosted bottles. A single fast shot causes a jetting streak that becomes a shiny line on the matte surface, visible under retail lighting. Ramping to fast in the middle fills the parison, then slowing at the end prevents flash at the gate and reduces internal stress that later shows as whiten around the neck. Back pressure of 3–8 bar keeps the melt homogeneous; too low invites silver streaks that read as defects on a matte field.

The core rod temperature is a lever unique to IBM. A warmer core rod keeps the parison interior soft so it slides off cleanly at strip and reduces residual stress; a colder rod gives a stiffer parison that holds shape but risks transfer drag. For frosted PP, 60–100 °C is the workable band, with higher values used when the bottle has long vertical walls that must not buckle during transfer.

4.2 파리송 컨디셔닝 스테이션(있는 경우)

On four-station machines, the conditioning station equalizes the parison wall temperature before blow. For frosted bottles this is valuable because it removes hot and cold spots that would otherwise copy the texture unevenly. Set the conditioning station to hold the parison at a uniform 95–125 °C for PP, slightly higher for PS, and let the wall thickness and blow-up ratio guide timing. Target a blow-up ratio of 2.5–4.5; ratios above 4.5 thin the skin so much that deep textures get smoothed away, while ratios below 2.5 leave too much material and a soft, undefined frost.

4.3 블로우 스테이션 설정 — 질감 전사 단계

이곳이 실제로 프로스트가 생성되는 곳이며, 블로우 압력 프로파일과 벤트 설계라는 두 가지 설정이 지배합니다.

ParameterTypical settingEffect on frosted finish
Low-pressure pre-blow2–4 barGently seats parison to cavity, pre-forms without blasting texture flat
High-pressure blow6–10 barForces skin into micro-relief for sharp, full texture transfer
Blow delay (ms)50–300 ms after clampLets parison relax so texture copies without drag lines
Blow flow rateHigh, short burstFast contact improves fidelity; too slow = soft frost
Vent / exhaust design0.02–0.05 mm deep, densifiedCritical: texture traps air, so vents must be finer and more numerous

The vent detail is the single most overlooked point in frosted bottle production. A smooth cavity vents air through the parting line and a few milled grooves. A textured cavity, however, creates thousands of tiny pockets that trap air between the parison and the relief; if the air cannot escape, the parison floats off the cavity and the frost comes out patchy or missing entirely. The correction is to densify the exhaust grooves to a depth of 0.02–0.05 mm and increase their number around the textured zone, especially near the shoulder and base where air pockets form first. This is the difference between a crisp frost and a rejected batch.

The pressure profile should start low to let the parison gently contact the cavity, then step to high pressure to push the skin into every micro-notch of the etched relief. A single high-pressure blast too early can stretch the parison so fast that it bridges over the texture instead of copying it, leaving glossy islands.

4.4 블로우 금형 온도 — 이송에 충분히 따뜻한 온도

A frosted bottle needs a higher blow mold temperature than a glossy bottle. The slight extra heat keeps the parison skin soft long enough to flow into the relief. For PP, run the blow mold at 25–45 °C, which is roughly 5–15 °C above the mold temperature you would use for a clear glossy PP bottle. Too cold and the texture is only partially transferred; too warm and the cycle stretches and the bottle may stick or show gate stress.

Surface goalPP blow mold tempResult
Glossy clear15–30 °CSharp mirror, no texture
Frosted (light)30–38 °CSoft matte, fine relief
Frosted (full sand-blast)38–45 °CDeep, even frost, longer cooling needed

트레이드오프는 냉각 시간입니다. 더 따뜻한 금형은 병이 굳기 위해 더 오래 클램핑되어 있어야 함을 의미하며, 이는 사이클에 초를 추가합니다. 아래 표는 동일한 크기의 광택 병과 비교하여 일반적인 사이클 분해와 프로스트 증가분을 정량화합니다.

Cycle segmentGlossy (s)Frosted (s)Frosted increment
Injection (parison)2.0–3.02.0–3.2+0.0–0.2
Holding / pack1.5–2.51.5–2.50
Cooling (parison)3.0–5.03.0–5.00
Turret rotation / transfer0.8–1.20.8–1.20
Blow / expand1.0–1.81.2–2.2+0.2–0.4
Blow mold cooling (set)4.0–6.05.5–8.5+1.5–2.5
Strip / eject0.6–1.00.6–1.00
Total per cavity-set13–2015–23+1.5–3.0

The honest conclusion is that a frosted bottle costs about 1.5–3.0 seconds more per cycle than its glossy twin, almost all of it in blow mold cooling. That penalty is recovered by raising mold temperature control precision and by designing the cooling circuit so the textured zone is held within ±2 °C, which lets you run at the low end of the warmer band rather than over-cooling.

5. 일반적인 결함 및 대책

프로스트 표면은 특정 결함을 증폭하고 다른 결함을 숨깁니다. 무광 필드는 사소한 플로우 라인을 숨기지만 부분적인 광택과 텍스처 드롭아웃을 확대합니다. 아래 표는 Aibim 공정 팀이 프로스트 IBM 병에서 가장 자주 보는 결함을 근본 원인 및 해결책과 함께 나열합니다.

#DefectRoot causeCountermeasure
1Texture transfer incomplete (glossy patches)Blow mold too cold; high pressure too early; poor ventingRaise blow mold temp 5–15 °C; use 2–4 bar pre-blow then 6–10 bar; densify 0.02–0.05 mm vents
2Patchy / uneven glossUneven wall temperature; inconsistent parison temp; mold temp driftAdd or tune conditioning station; tighten mold temp control to ±2 °C; verify core rod temp
3Texture worn to gloss (after run)Mold steel too soft; abrasive masterbatch; long runUse hardened steel or PVD coating; plan re-etch cycle; reduce filler abrasion
4White specks / silver streaksTrapped moisture or gas; low back pressure; degraded resinDry resin; raise back pressure to 3–8 bar; lower melt temp; check regrind ratio
5Demolding drag marks (matte scraped shiny)Texture increases release friction; draft angle too smallIncrease draft angle from 0.5° to 1–1.5°; improve ejection; verify mold release
6Neck finish flashParison over-pack; mold parting not sealed; clamp lowReduce holding pressure; check parting line; verify clamp force
7Wall thickness unevenParison programming off; core rod eccentric; transfer misalignRe-profile parison; center core rod; verify turret indexing
8Sink marks at neck or baseInsufficient holding; thick section; cooling unequalRaise holding pressure and time; balance cooling circuit
9Bubbles / voidsVolatiles in melt; moisture; screw decompressDry material; lower melt temp; adjust back pressure and decompression
10Color shade variationMasterbatch let-down drift; batch change; shear heatStabilize let-down; lock recipe on SD card; monitor melt temp
11Fingerprint visibility on matteMatte surface traps oils; low surface energySpecify finer etch for less oil grab; advise handling; consider soft-touch top coat offline
12Base ovality / poor standingBlow ratio too high; base not supported; cooling shortReduce blow-up ratio toward 2.5–4.5; extend base cooling; check base vent

Two of these deserve emphasis because they are unique to frosted bottles. Number 5, demolding drag, appears because the micro-relief that creates the frost also increases the surface area and mechanical interlock at release; the standard 0.5° draft angle that works on a glossy bottle is often insufficient, and raising it to 1–1.5° is the routine correction. Number 1, incomplete texture transfer, is almost always a venting or mold-temperature problem, not a material problem, which is why the vent depth of 0.02–0.05 mm and the warmer mold band are stressed throughout this article.

6. 무광(프로스티드) 마감을 위한 금형 설계 포인트

블로우 금형은 프로스트 병의 진정한 도구입니다. 금형을 잘 설계하는 것이 텍스처가 백만 사이클을 견디는지 결정합니다. 다음 사항은 Aibim이 IBM 라인을 위해 제작하고 텍스처링하는 금형을 안내합니다.

Texture uniformity and parting-line transition. The etch must wrap the cavity continuously, including across the shoulder and into the base. Where the parting line crosses the textured zone, the two halves must align within a few microns or a visible seam appears. Aibim programs the etch mask so the parting line falls in a non-critical area or is blended by a transition zone.

에칭 전에 베이스를 폴리싱하십시오. 에칭은 시작 표면을 증폭시킵니다. 캐비티는 먼저 깨끗한 SPI 베이스 마감으로 폴리싱되어 프로스트가 무작위 피팅이 아닌 일관된 그레인으로 보이게 합니다. 불량한 베이스는 얼룩지고 더러운 무광을 만듭니다.

Coating choice. Hard chrome, electroless nickel-phosphorus, and PVD coatings each change the texture. Chrome is hard and releases well but can soften fine etch edges over re-chromes; nickel-phosphorus holds micro-relief precisely and resists many cosmetic oils; PVD gives the highest wear resistance for long abrasive runs. The coating is matched to the resin and run length.

Mold material. A frosted cavity wears faster than a glossy one because the relief edges are thin and carry release stress. Aibim uses pre-hardened tool steel (P20-type) for most runs and stainless tool steel (420-type) where corrosion resistance against cleaning and certain formulations is required. Both are selected for higher wear resistance than a standard mold steel.

Texture repair and re-etch cycle. After a production run the relief can round off; rather than scrap the mold, the cavity is re-polished and re-etched to the same VDI 3400 grade, restoring the original frost. Planning this cycle into preventive maintenance keeps the finish consistent across years of production.

냉각 레이아웃. 텍스처 구역은 ±2°C 내로 유지되어야 합니다. Aibim은 숄더, 몸체 및 베이스 모두가 균형 잡힌 유량을 받도록 배플 및 버블러 냉각을 설계합니다. 텍스처 밴드의 핫스팟은 어떤 매개변수 조정으로도 완전히 숨길 수 없는 광택 패치를 만들기 때문입니다.

7. 품질 검사 및 정량적 인수

무광 병은 외관과 물리적 성능 모두에서 승인됩니다. 아래의 측정 가능한 기준은 Aibim이 텍스처 시험과 입고 생산 로트에서 기록하는 기준입니다.

TestStandardTypical frosted acceptancePurpose
HazeASTM D100315–60 % depending on gradeConfirms matte diffusion level
Gloss 60°ASTM D245710–55 GUConfirms low-reflective finish
Surface roughness RaISO 4287 / profile0.4–3.0 μm on etched zoneQuantifies micro-relief depth
Texture depthProfilometer2–25 μm by VDI gradeLinks etch grade to look
Color ΔECIE Lab< 1.5 between lotsBatch-to-batch consistency
Abrasion / rubTaber / crockNo gloss rise after set cyclesFrost durability in handling
Drop testInternal / ASTM D5276No crack at specified heightTransport robustness
Sealing integrityLeak / torqueNo leak at cap torqueClosure performance

The two optical measures, haze per ASTM D1003 and gloss 60° per ASTM D2457, are the daily checks. A frosted bottle that drifts above its gloss ceiling is reading as too shiny; one that climbs in haze beyond spec is reading as too cloudy, usually from contamination or an additive shift. Surface roughness Ra and profilometer texture depth tie the look back to the VDI 3400 etch grade so the finish is documented, not guessed. Color ΔE under 1.5 keeps a brand’s matte bottle identical across reorders, which is exactly what cosmetic and pharmaceutical buyers require.

8. Aibim 사출 블로우 몰딩 기계

Aibim, a Wanplas factory with 12+ years in plastic machine manufacturing and 20 years in injection blow molding, builds three-station one-step I(S)BM machines from 3 mL to 1000 mL, with its own CNC center and a 100+ lines-per-year capacity from a new factory established in 2022. The machines carry CE certification, a minimum 35% energy saving through PREFILL technology and variable displacement pump pressurizing, and SD-card recipe storage so a validated frosted process moves from one machine to another without re-tuning. Below are two of the real series used for frosted bottle programs.

8.1 IBM75 사출 블로우 성형 기계

The IBM75 is the flagship for mid-to-large frosted bottles such as 200 mL lotion bottles, 500 mL toner bottles, and 1000 mL body wash containers. Its wider platen and higher clamp accept multi-cavity molds with deep-etched blow cavities, and its conditioning-friendly turret supports the even-wall temperature that frosted finishes need.

SpecificationIBM75
클램핑 포스75 ton (750 kN)
Injection screw diameter45 mm
Screw L/D ratio20:1
Theoretical shot volume290 cm³
Max. preform weight280 g
Max. bottle volume1000 mL
Cavity number2–8 (by bottle size)
Mold platen size (H×V)460 × 460 mm
Max. bottle height240 mm
건조 사이클 시간~2.0 s
Installed power33 kW
Heating power14 kW
기계 무게~4.8 t
Machine dimensions3.6 × 1.6 × 2.2 m

8.2 IBM65 사출 블로우 성형 기계

IBM65는 30~500mL 프로스트 화장품 및 의약품 병을 위한 균형 잡힌 워크호스입니다. 약간 더 작은 설치 면적과 충분한 캐비티 수를 결합하여 진지한 생산량을 제공하며, 세럼 드로퍼, 에센스 병 및 100mL 토너의 일반적인 선택입니다.

SpecificationIBM65
클램핑 포스65 ton (650 kN)
Injection screw diameter40 mm
Screw L/D ratio20:1
Theoretical shot volume220 cm³
Max. preform weight210 g
Max. bottle volume500 mL
Cavity number2–6 (by bottle size)
Mold platen size (H×V)420 × 420 mm
Max. bottle height200 mm
건조 사이클 시간~1.8 s
Installed power28 kW
Heating power12 kW
기계 무게~4.0 t
Machine dimensions3.3 × 1.5 × 2.1 m

For buyers prioritizing the lowest energy use on smaller 10–250 mL frosted bottles, the IBM55 Hybrid Electric adds a servo-electric assist to the hydraulic clamp, extending the 35% energy saving further on light parts while keeping the same three-station one-step process and the same textured blow mold standard. All three machines share Aibim’s SD-card recipe system, so a frosted process developed on an IBM75 transfers to an IBM55 without re-deriving the window.

9. 응용 산업 및 용기 크기

Aibim 기계는 의약품, 식품, 음료 및 화장품 시장에 서비스를 제공하며, 프로스트 마감은 프리미엄, 미끄럼 방지, 광 확산 외관이 품질을 전달하는 곳에서 특히 가치가 있습니다. 구체적인 최종 제품과 일반적으로 사용되는 용량:

  • 화장품 및 개인 관리: 에멀전 병(30 / 50 / 100 mL), 세럼 및 에센스 병(10 / 30 mL), 토너 병(100 / 200 mL), 페이스 미스트 및 스플래시 병(100 / 200 mL). 부드러운 촉감의 무광을 위해 프로스트 PP와 PETG가 여기서 지배적입니다.
  • 향수: 무광 표면이 빛을 확산시키고 액체 수위 변화를 숨기는 10/30/50mL 프로스트 스프레이 및 롤러 병.
  • 의약품 경구 액제: 측정 용량 시럽 및 용액용 10/30 mL 무광 PP 또는 PS/SAN 병으로, 무광 마감이 고령 사용자의 파지(쥐기)를 돕습니다.
  • 건강 보조식품: 자연스러운 포지셔닝을 나타내는 소프트 프로스트가 적용된 PETG 또는 PCTG 50/100mL 드로퍼 병.
  • 데일리 케미컬: 미끄럼 방지 무광이 기능적인 100/200mL 손 소독제 및 로션 병.
  • 유아 및 아동 케어: 투명하지만 부드러운 프로스트가 안전 등급 수지와 결합된 30/50mL 순한 포뮬러 병.
  • 프리미엄 주류 미니: 프로스트 처리된 몸체가 선물 포장의 일부인 50/100mL 샘플러 병.

반복되는 10 / 30 / 50 / 100 / 200 mL 사다리는 실용적인 지도입니다: 소형은 IBM55 Hybrid, 중형은 IBM65, 그리고 더 큰 200–1000 mL 프로스트 병은 멀티 캐비티 금형을 갖춘 IBM75가 적합합니다.

10. 요구사항-모델 선택 표

표는 구매자의 실제 변수(병 용량, 재료, 연간 생산량 및 원하는 프로스트 수준)를 권장 Aibim 모델 및 캐비티 수에 연결합니다. 생산량 수치는 2교대 운영과 표준 사이클을 가정하며, 정확한 병과 금형에 대해 검증하십시오.

Bottle volumeMaterialAnnual outputFrost levelRecommended modelCavities
10–30 mLPP / PETGLow–MediumLight–FullIBM55 Hybrid4–8
30–50 mLPP / PS / SANMediumFull sand-blastIBM654–6
50–100 mLPP / PETG / PCTGMedium–HighLight–FullIBM652–6
100–200 mLPP / PETGMedium–HighFullIBM65 / IBM752–4
200–500 mLPP / PETGHighFullIBM752–4
500–1000 mLPPHighMedium–FullIBM752
Any, multi-resin trialPP / PS / PETGLaboratoryAll gradesIBM65 (R&D mold)1–2

The selection logic is simple: pick the smallest machine whose clamp and platen can hold the required cavity count at the target bottle size, then choose the etch grade (VDI 3400 21–45) that delivers the frost level, and set the blow mold temperature at the warmer band with densified vents. Aibim’s process team locks this recipe to an SD card so reorders run identically.

11. Aibim의 서비스 및 지원

프로스트 병 라인을 구매하는 것은 단순한 강철이 아니라 재현 가능한 공정을 구매하는 것입니다. Aibim은 Wanplas 공장으로서 모든 기계에 그룹의 공동 약속과 자체 IBM 특화 전문성을 제공합니다.

  • 선적 전 테스트: 각 기계는 텍스처 금형을 포함한 연속 시험을 실행하여, 라인이 공장을 떠나기 전에 무광 처리 제품이 검증됩니다.
  • 금형 시험 및 텍스처 샘플링: Aibim은 고객 수지로 캐비티 에칭 및 블로우 시험을 수행하여 양산 전에 승인된 탁도 및 광택 샘플(ASTM D1003 및 ASTM D2457 기준)을 제공합니다.
  • 설치 및 시운전: 엔지니어가 고객 현장에서 검증된 레시피에 맞춰 기계, 금형, 냉각을 설정합니다.
  • 예비 부품: Wanplas 그룹 정책은 매년 USD 500 상당의 무료 부품을 제공하며 손상 부품은 보증 교체합니다.
  • 교육: 작업자는 패리슨 프로그래밍, 금형 온도 제어, 벤트 유지보수, 텍스처 재식각 일정을 배웁니다.
  • 원격 운영 및 유지보수: SD 카드 레시피 시스템과 선택적 원격 모니터링을 통해 Aibim이 공정 데이터를 확인하고 신속한 문제 해결을 지원할 수 있습니다.
  • 오픈 팩토리: 고객은 구매 전후에 장자강(Zhangjiagang) 공장을 방문하여 CNC 센터를 둘러보고 생산 라인을 감사할 수 있습니다.

Wanplas는 전문 공장 네트워크를 운영하므로 매칭된 충전 및 하류 포장과 같은 인접 역량을 Wanplas 그룹을 통해 조정할 수 있어 프로젝트를 하나의 신뢰할 수 있는 공급망 내에서 유지할 수 있습니다.

Closing invitation. If you are specifying frosted finish bottles — whether a 10 mL serum dropper or a 1000 mL body wash container — send Aibim your bottle drawing, target material, required frost level, and annual volume. The team will propose the right IBM model, design and etch the blow mold, run a texture sample on your resin, and invite you to the factory for a trial run and audit. No two frosted finishes are identical, and the fastest path to a consistent matte is a jointly developed, documented process.

12. 자주 묻는 질문

사출 블로우 성형기에서 프로스트 마감 병을 만드는 가장 좋은 방법은 무엇인가요?

The most reliable route is in-mold texture: etch or sandblast the blow mold cavity to a VDI 3400 grade of 21–45, then blow the parison against the warm cavity so the skin copies the relief. It gives single-material recyclability, no recurring consumable cost, and shot-to-shot consistency that additive or post-coat methods cannot match.

질감이 사출 금형이 아닌 블로우 금형에 적용되는 이유는 무엇입니까?

The parison injected on the core rod is smooth, and the visible bottle surface is created only when the soft parison is expanded against the blow cavity. Etching the blow cavity lets the relief transfer during blow-up; etching the injection mold would only texture the parison exterior, which is then stretched and pressed into the blow cavity where the texture would be lost or distorted.

어떤 소재가 가장 깨끗한 프로스트 마감을 제공하나요?

PP is the best all-round choice because its naturally low haze lets the etched relief read as an even matte, and its broad melt window tolerates the slightly higher blow mold temperature that texture transfer needs. PS and SAN give the strongest contrast on a clear base but are more brittle, while PETG and PCTG give a softer premium satin.

프로스트 병에 더 높은 블로우 몰드 온도와 더 긴 냉각이 필요한 이유는 무엇인가요?

The slightly warmer cavity keeps the parison skin soft long enough to flow into the micro-relief, so the frost transfers fully. For PP, run the blow mold at 25–45 °C, about 5–15 °C above a glossy bottle. The cost is roughly 1.5–3.0 extra seconds of blow mold cooling per cycle, recovered by tight ±2 °C mold temperature control.

프로스트 병에 배기 벤트가 왜 그렇게 중요한가요?

A textured cavity traps air in thousands of tiny pockets; if that air cannot escape, the parison floats off the relief and the frost comes out patchy or missing. The correction is to densify the vent grooves to a depth of 0.02–0.05 mm and increase their number around the textured zone, especially at the shoulder and base.

무광 병이 이젝션 후 때때로 반짝이는 드래그 마크를 보이는 이유는 무엇입니까?

미세 요철은 이형 마찰을 증가시키므로 광택 병에 사용되는 표준 0.5° 드래프트 각도는 종종 충분하지 않으며 무광 표면이 탈형 중에 긁혀 광택이 나게 됩니다. 드래프트 각도를 1~1.5°로 높이고 금형 이형을 확인하면 일반적으로 결함이 제거됩니다.

프로스트 마감은 어떻게 측정되고 합격 처리되나요?

헤이즈는 ASTM D1003에 따라, 60° 광택은 ASTM D2457에 따라 측정되며, 표면 거칠기 Ra와 프로필로미터 텍스처 깊이가 외관을 VDI 에칭 등급과 연결합니다. 색상 일관성은 로트 간 ΔE 1.5 미만으로 추적되며, 낙하, 밀봉 및 마모 테스트가 물리적 성능을 확인합니다.

100mL 무광 화장품 병에 어떤 Aibim 기계를 선택해야 합니까?

중간~높은 출력에서 PP 또는 PETG로 된 100mL 프로스트 병의 경우 2~6개 캐비티의 IBM65가 일반적인 선택입니다. 더 작은 10~30mL 생산은 IBM55 Hybrid에 적합하며, 더 큰 200~1000mL 프로스트 병은 IBM75로 이동합니다. 정확한 캐비티 수는 연간 생산량과 사이클 목표에 따라 달라집니다.