사출 블로우 몰딩 머신

블로우 압력 조정 가이드: 다양한 플라스틱 소재에 대한 최적 설정

목차

블로우 압력이 단일 수치가 아닌 시스템인 이유

Aibim, a Wanplas factory based in Zhangjiagang, has manufactured injection (stretch) blow molding machines for more than 12 years, with 20 years of accumulated know-how in the injection blow molding field. Our lines serve customers in over 40 countries, run from our own CNC machining center, and produce more than 100 lines per year from a new factory established in 2022. Container sizes span from 3 ml medical droppers to 1000 ml cosmetic and food bottles. The single most misunderstood parameter among new operators is blow pressure. Many buyers ask for “the right blow pressure” as if it were one number printed on a dial. In reality, blow pressure is a system. It is the combination of a low-pressure preblow stage and a high-pressure final blow stage, multiplied by timing, material behavior, parison or preform temperature, mold temperature, and bottle geometry.

This guide explains blow pressure as a controllable process window rather than a fixed setpoint. We cover the physics of gas pressure pushing molten polymer against a cold mold cavity, the two-stage pressure architecture used on Aibim three-station one-step IBM machines, how pressure interacts with temperature and timing, and a full material-by-material table of optimal pressure windows. Whether you run PET, PP, PE, PS, SAN, PC, ABS, or TPU, the methodology below lets you move from a generic starting point to a verified, repeatable pressure recipe stored on the machine’s SD card.

Key Statistics
– Aibim: 12+ years of machine manufacturing, 20 years in injection blow molding know-how
– Exported to 40+ countries; 100+ lines per year capacity
– Container range 3 ml to 1000 ml; three-station one-step IBM process
– PREFILL hydraulic technology saves a minimum of 35% energy versus conventional hydraulic lines
– CE certified with light curtain and laser sensor safety systems

병 성형에서 블로우 압력의 물리학

Blow pressure exists for one physical purpose: to drive the molten polymer of the parison or preform outward until it contacts every surface of the blow mold cavity, then to hold it there while it freezes and takes the final shape. In injection blow molding the parison is injected as a tubular blank at the first station, transferred to the blow station, and expanded by compressed air. The air pressure does mechanical work against the polymer’s viscosity and against the heat-transfer rate of the mold wall.

When blow pressure is too low, the polymer cannot overcome its own viscosity and the mold’s cooling effect before it solidifies. The result is poor mold contact, shallow detail, thick-and-thin wall distribution, and weak structural zones. When blow pressure is too high, the polymer is forced into a thin, over-stretched skin that loses mechanical strength, develops internal stress, risks burst during the cycle, accelerates mold wear, and wastes compressed-air energy. The correct pressure is therefore a balance point where the material fully contacts the cavity with the minimum air energy required.

Air pressure also interacts with the rate of pressure rise. A steep, instant step from zero to maximum pressure can trap the material unevenly and create localized stress marks, while a controlled ramp that begins with a gentle preblow and rises to final blow gives the material time to distribute before it sets. This is why a two-stage system outperforms a single fixed pressure for bottles with non-uniform geometry.

The pressure required to move the polymer is a function of its extensional viscosity at the moment of blowing. A polymer that is still hot and soft extends at low pressure; the same polymer a few seconds later, after the mold has pulled heat from its surface, may need double the pressure to move the same distance and will instead tear or thin. This is the central reason blow pressure cannot be set without also controlling temperature and time. The operator is, in effect, racing the freeze front: pressure must arrive while the material is still mobile enough to flow, but not so early or so hard that it stretches the wrong zone.

Another physical factor is the surface area the air must push against. As the bubble grows, its internal volume rises with the cube of the radius while the wall area rises with the square, so the local stress in the wall drops as the bottle expands, provided the material keeps thinning evenly. If the pressure is too low, the bubble stalls before it reaches the cavity corners and the wall freezes in a thick, uneven state. If the pressure is too high, the bubble reaches the wall so fast that the material has no time to redistribute, producing a thin spot opposite the injection point and a thick ring near the neck. Reading the wall-thickness profile after a trial shot tells you far more about the correct pressure than the pressure gauge alone.

2단계 압력 시스템: 프리블로우 및 최종 블로우

Aibim IBM 기계에서 공압 회로는 두 개의 제어 단계로 나뉩니다. 각 단계의 역할을 이해하는 것이 올바른 튜닝의 기초입니다.

프리블로우 압력(저압 단계)

The preblow stage applies a low air pressure the moment the parison or preform enters the blow mold. Its job is to begin the expansion, establish the initial bubble shape, and guide where the material will go before the high pressure arrives. Preblow pressure and preblow timing together decide the wall-thickness distribution more than any other single variable. If the preblow is too weak or arrives too late, the material collapses onto the mold base before it has spread upward, leaving a thick bottom and a thin shoulder. If the preblow is too strong or arrives too early, the material stretches prematurely and thins in the zone that still needs material later.

재료별 일반적인 프리블로우 윈도우는 아래 재료 표에 자세히 나와 있지만, 개념적으로 PET 또는 PCTG와 같은 배향 재료의 프리블로우는 종종 약 8~16bar이고, LDPE 또는 TPU와 같은 연질 재료는 약 4~9bar에 가깝습니다.

최종 블로우 압력(고압 단계)

The final blow stage applies the high pressure that completes cavity contact, forms fine detail such as embossing or threads, and sets the bottle dimensions. Final blow pressure is held for a defined dwell, then vented. For PET the final blow commonly ranges 25 to 40 bar; for PP, PE, PS, and PC the windows differ and are listed per material. After the high-pressure dwell, a short exhaust and cooling phase lets the part solidify enough for transfer to the ejection station.

사출 블로우 몰딩의 차이점

In IBM the parison is injection-molded with precise wall distribution, then blown in a separate station on the same machine. Compared with extrusion blow molding, where the parison is extruded and hotter with more sag, IBM parisons are cooler and more controlled, so the blow pressure requirement is steadier and the scrap rate lower. Compared with two-step stretch blow molding of PET, IBM performs the blow on a preform that was just injected rather than re-heated, which removes the reheat oven variable but still requires correct blow pressure and timing for full orientation.

블로우 압력이 온도, 타이밍, 금형과 어떻게 연동되는가

블로우 압력은 단독으로 튜닝하지 않습니다. 압력, 온도, 타이밍의 삼각 관계에 속합니다. 한쪽을 바꾸면 다른 쪽도 바꿔야 합니다.

  • 온도 연동: 더 따뜻한 패리슨이나 프리폼은 더 낮은 압력에서 흐릅니다. 배럴이나 금형 온도를 올리면 블로우 압력을 낮춰도 완전한 접촉을 얻을 수 있는 경우가 많습니다. 더 차가운 부품은 더 많은 압력이 필요하지만, 차가운 재료에 너무 많은 압력을 가하면 응력과 파열 위험이 발생합니다.
  • 타이밍 연동: 프리블로우 지연과 파이널 블로우 유지 시간은 타이밍 레버입니다. 프리블로우 지연은 재료를 아래로 이동시키고, 긴 파이널 유지 시간은 디테일을 개선하지만 사이클과 에너지 사용을 늘립니다.
  • 금형 온도 연동: 금형 온도는 냉각 속도를 제어합니다. 차가운 금형은 선명한 디테일을 위해 더 높은 압력을 사용할 수 있지만 응력 위험이 있습니다. PP와 같은 결정화 가능 재료의 따뜻한 금형은 결정화를 제어하지만 처짐을 방지하기 위해 압력 조정이 필요합니다.
  • 형체력 연동: 블로우 압력은 캐비티 내부 표면에 작용합니다. 충분한 형체력은 파팅 라인의 버(flash)를 방지합니다. 형체력이 충분하지 않은 상태에서 블로우 압력을 높이면 더 나은 병이 아니라 버가 발생합니다.

실용 규칙: 먼저 온도 윈도우를 설정하고, 그다음 프리블로우로 분포를 설정하고, 파이널 블로우로 접촉을 확보한 후 타이밍을 다듬습니다. 온도와 타이밍을 무시하고 압력 값만 변경하여 결함을 해결하려 하지 마십시오.

패리슨 벽 설계와 블로우 압력에 미치는 영향

In injection blow molding the parison is not a neutral tube; its wall thickness profile is set at the injection station and directly determines how much blow pressure is needed and where. A parison with a heavier base and lighter shoulder will need less final blow pressure at the bottom and more at the top. A parison with uniform wall needs a more uniform pressure ramp. Because the parison wall is programmable through the injection and core-rod design, the blow pressure window is really the second half of a two-part control system: injection sets the material budget, blow pressure spends it.

This coupling means a pressure problem is sometimes solved at the injection end rather than the blow end. If a bottle consistently shows a thin shoulder regardless of final blow pressure, the parison is likely too light at the shoulder and no amount of air will move material that is not there. Adding parison weight at that zone, or shifting the core-rod program, reduces the required blow pressure and improves the result. Conversely, an over-heavy parison forces you to raise pressure merely to spread excess material, which wastes energy and stresses the mold. Treating parison design and blow pressure as one loop is the fastest route to a stable recipe.

스트레치 로드 상호작용

On machines that include a stretch step, the stretch rod physically lengthens the preform before the air arrives. The rod sets the axial orientation; the blow pressure sets the radial orientation. If the rod moves too far before the preblow, the material is already thin axially and the final blow will over-thin the side wall. If the rod moves too late, the preblow alone must do the axial work and will need a higher pressure than the material tolerates. The pressure recipe therefore includes the stretch rod speed and start point as hidden variables, especially for PET and PCTG where biaxial orientation defines quality.

재료별 최적 블로우 압력 설정

The table below gives engineering windows for each material processed on Aibim IBM machines. These are typical starting ranges, not guaranteed setpoints; always verify on the actual mold and material grade, and store the confirmed recipe on the SD card. Process temperature is the melt temperature in the barrel; mold temperature is the blow cavity temperature; hold time is the final-blow dwell.

Read the table as a band, not a point. Within each band, the correct value depends on wall thickness, bottle size, and cavity count. A thicker-wall bottle sits at the lower edge of the final-blow band because the material has more mass to push but less distance to travel; a thin-wall large bottle sits higher because the air must drive a light shell fully into a large cavity before it freezes. When moving between grades of the same polymer, raise the pressure slightly for higher molecular weight or higher filler content, and lower it for easier-flow grades. The per-material notes that follow explain the behavior behind each band so you can reason about adjustments instead of guessing.

Material Process Temp (°C) Preblow (bar) Final Blow (bar) Hold Time (s) Mold Temp (°C) Typical Defect Linkage
PET 260–285 8–16 25–40 1.5–3.0 10–25 Low orientation if preblow weak; haze if over-pressured
PCTG 255–280 8–15 24–38 2.0–3.5 20–40 Stress marks if cooled too fast
PP (clarified) 220–260 6–12 20–34 2.0–4.0 20–60 White stress marks if pressure ramps too fast
HDPE 200–230 5–10 16–30 2.0–4.0 10–40 Softness; needs good cooling before eject
LDPE / LLDPE 180–220 4–9 14–26 2.0–4.0 10–40 Low rebound; risk of sticking
PS 200–240 6–12 18–30 1.5–3.0 20–50 Brittle; bursts if final blow too high
SAN 210–250 7–13 20–32 2.0–3.5 40–70 Needs warm mold for gloss; sensitive to over-pressure
PC 280–320 10–18 30–45 3.0–6.0 80–120 High dry requirement; stress cracks if over-pressured
ABS 210–250 7–13 22–36 2.5–4.5 50–80 Opaque; tolerant, medium pressure
TPU 190–230 4–9 14–26 3.0–6.0 20–60 Soft elastic; sticking and rebound control needed

PET 및 PCTG

PET and PCTG are orientation-sensitive. PET must be dried below about 50 ppm moisture before processing, and the preblow establishes the biaxial orientation that gives the bottle its strength and clarity. A weak preblow leaves the material un-oriented and cloudy; a correct preblow followed by a 25–40 bar final blow gives a clear, strong bottle. PCTG is less moisture-sensitive than PET but still benefits from a controlled ramp; over-pressure on a fast-cooling cavity produces stress whitening rather than crisp detail.

PP

PP is crystallizable and temperature-sensitive. Clarified PP for transparent bottles needs a warm enough mold to control crystallization, yet too warm a mold causes sag that must be countered by adjusting pressure timing rather than by raising pressure blindly. A gentle pressure ramp reduces the white stress marks common in PP. The window of 6–12 bar preblow and 20–34 bar final blow suits most PP bottles.

PE (HDPE, LDPE, LLDPE)

Polyethylene is soft and has low rebound, so it needs relatively low blow pressure. HDPE suits 16–30 bar final blow; LDPE and LLDPE need even less because they are more flexible and tend to stick to the cavity. Cooling and demolding control matter more than raw pressure for PE. Over-pressuring PE wastes air and can flash at the parting line without improving the bottle.

PS 및 SAN

PS is intrinsically transparent but brittle. Final blow above the material’s comfort band causes burst or micro-cracks. A gentle, well-timed pressure rise is essential. SAN is similar but more chemical-resistant and glossy; it wants a warmer mold (40–70 °C) for surface gloss and a moderate pressure that does not over-stress the part.

PC

PC has high viscosity and demands high drying (below about 50 ppm) plus high process temperature (280–320 °C) and a warm mold (80–120 °C) to avoid stress. Blow pressure is among the highest of the common materials, 30–45 bar final, but the pressure must rise smoothly to avoid internal stress cracking. PC bottles are usually for medical or reusable drinkware where dimensional stability is critical.

ABS

ABS는 불투명하고 강인하며 관용적입니다. 중간 압력(파이널 22~36bar)이면 충분합니다. 투명도보다 색상과 표면 마감이 더 중요한 화장품 및 퍼스널케어 용기에 선택됩니다. 일반 건조 외에 특별한 건조는 필요하지 않으며, 좋은 표면을 위해 금형을 따뜻하게 가동할 수 있습니다.

TPU

TPU는 부드럽고 탄성이 있습니다. 탄성 메모리로 인해 들러붙음과 반동이 발생할 수 있으므로 저압(파이널 14~26bar)과 주의 깊은 탈형이 필요합니다. 이젝션 전에 더 긴 유지와 냉각은 변형을 줄입니다. TPU 병은 특수 의료 및 소프트 터치 화장품 응용 분야에 사용됩니다.

병 형상 및 벽 두께에 따른 압력 보정

원형 100ml 병에 맞는 압력 레시피는 손잡이가 있는 750ml 비대칭 병에서는 실패할 수 있습니다. 아래 표는 재료 기본 윈도우 위에 적용하는 보정 규칙을 제공합니다.

Bottle Type Preblow Correction Final Blow Correction Timing Note
Thin wall (≤ 0.4 mm) Slightly higher to avoid early contact High, for full cavity contact Shorten high-pressure dwell to limit thinning
Thick wall (≥ 1.2 mm) Lower and later Extend dwell and hold Longer hold for complete freeze
Large volume (> 500 ml) Lower, delayed preblow Extend final dwell Manage cooling, watch cycle time
Small volume (< 50 ml) Higher preblow Moderate final Fast cycle, short dwell
Handle or asymmetric Zone-balanced Higher at fill stage for handle Delay to fill recessed zones
Wide mouth Lower preblow Moderate final Watch neck finish
Narrow neck Moderate Ensure base fills first Confirm base before neck pressure

단계별 압력 튜닝 방법론

새 재료, 새 금형 또는 새 병 크기를 시작할 때마다 다음 의사결정 흐름을 사용하십시오. 이 흐름은 압력, 온도, 타이밍을 올바른 순서로 유지합니다.

>
Step Action Set / Adjust Verify
1 Fix material temperature window Barrel and mold temp per material table Melt flows, no degradation
2 Set preblow to form bubble Preblow bar and delay per material Even early expansion, no collapse
3 Set final blow for contact Final blow bar and ramp rate Full cavity contact, detail formed
4 Fine-tune timing Preblow delay, final dwell, exhaust Wall distribution balanced
5 Validate the part Measure wall, volume, burst, top load Within spec; no stress marks
6 Save and reuse Store recipe on SD card Same recipe runs on sister machines

파이널 블로우 윈도우의 하한에서 시작하여 완전한 캐비티 접촉이 달성될 때까지만 증가시키십시오. 최소값 이상의 모든 증가는 낭비되는 압축 공기 에너지입니다. 승인된 수치를 문서화하여 다른 IBM65 또는 IBM75에서 처음부터 재튜닝 없이 레시피를 재로드할 수 있게 하십시오.

압력 관련 불량: 증상 및 조정 빠른 참조

다음 표는 일반적인 블로우 결함을 압력 관련 조정 방향에 매핑합니다. 1차 대응 카드로 취급하고, 항상 온도 및 타이밍 점검으로 확인하십시오.

# Symptom Likely Pressure Cause Adjustment Direction
1Poor mold contact / incomplete formingFinal blow too low or delayedRaise final blow; check preblow timing
2Thin wall in shoulder or sidePreblow too early/strong, uneven parisonLower or delay preblow; adjust parison temp
3Thick wall / material pooling at basePreblow too late, final too lowAdvance preblow; raise final blow
4Bottle burst during cycleFinal blow too high or ramp too steepLower final blow; soften ramp
5White stress marks (PP/PE)Pressure ramp too fast, cold materialReduce pressure rate; raise temp
6Flash at parting lineFinal blow exceeds clamping forceLower final blow; verify clamping force
7Neck or finish deformationLocal over-pressure at neckReduce blow at neck; check mold temp
8Unstable base / rockingPreblow timing wrong, base not setAdjust preblow timing; lower final slightly
9Poor detail / embossing unclearFinal blow too low or dwell shortRaise final blow; extend dwell
10Internal stress cracking (PC/PS)Over-pressure, fast coolingLower pressure; raise mold temp; anneal
11Ovality / distortion after ejectPressure-cooling imbalanceBalance pressure with cooling time
12Weld line at handleInsufficient fill-stage pressureRaise final at handle stage; adjust parison
13Surface haze from over-pressureFinal blow too high for materialReduce final blow
14Short shot / incomplete fillAir volume or final blow insufficientRaise final blow; check air supply volume
15Pinch-off too thin / leakClamping and pressure mismatchVerify clamping; tune pressure
16Residual pressure trapExhaust timing too lateAdvance exhaust; check valve

일반적인 압력 설정 실수

숙련된 작업자조차 위 방법이 방지하도록 설계된 몇 가지 실수를 반복합니다. 이를 인지하면 튜닝 시간이 단축됩니다.

  • 온도보다 먼저 압력 설정: 배럴 또는 금형 온도가 잘못되면 어떤 압력 값도 의미가 없습니다. 온도를 먼저 바로잡으십시오.
  • 압력을 높여 한 결함을 해결하려는 시도: 얇은 숄더는 파이널 블로우를 높여도 거의 해결되지 않습니다. 패리슨 중량이나 프리블로우 타이밍으로 해결됩니다. 압력을 더 높이면 문제가 다른 곳으로 옮겨갈 뿐입니다.
  • 여러 재료에 하나의 레시피 사용: PET와 PP는 서로 대체할 수 없습니다. 레시피는 수지 등급에 따라 변경되어야 합니다.
  • 램프 속도 무시: 최고값보다 도달 속도가 더 중요합니다. 부드러운 램프는 파열과 응력 자국을 방지합니다.
  • 레시피 미저장: SD 카드에 검증된 레시피도 재료와 병별로 저장되고 라벨링되지 않으면 잃어버린 지식입니다.
  • 안전 여유를 위한 과도한 압력: 최소값보다 20% 높은 압력 여유는 거의 도움이 되지 않으며 항상 공기를 낭비하고 금형을 마모시킵니다.

공압 시스템 및 에너지 효율

Compressed air is one of the largest hidden costs in blow molding. Aibim machines use PREFILL technology and a variable displacement pump pressurizing system in the hydraulic circuit, and a staged high-low pressure air system for the blow function. The energy-saving design reduces consumption by a minimum of 35% compared with conventional hydraulic lines.

Air quality matters. For food, pharmaceutical, and cosmetic bottles the compressed air should be oil-free and dried to a clean class consistent with ISO 8573-1 concepts (oil, water, and particle limits). Contaminated air leaves odors or particles in the bottle and can foul valves. A staged supply separates the low-pressure preblow line from the high-pressure final-blow line so the compressor does not run everything at maximum pressure.

Air recovery, where practical, captures vented blow air or recovers expansion energy, lowering the effective energy per bottle. Even without full recovery, right-sizing the receiver, stabilizing line pressure, and only using the minimum final blow needed already cut air cost substantially. The table below compares energy and air indices using a baseline of 100 index points.

Configuration Air Energy Index Relative Cost vs Baseline
Conventional fixed pump, single pressure135High1.35× baseline
Staged high-low air, no recovery110Medium1.10× baseline
Aibim PREFILL + variable pump + staged air65Low0.65× baseline (35% saved)
Above with air recovery add-on52Low0.52× baseline

고압 공기 시스템 안전

파이널 블로우 압력은 25~45bar에 이르며, 압축 공기 시스템은 실제 위험을 수반합니다. Aibim 기계는 CE 인증을 받았으며 인원 안전을 위한 라이트 커튼과 금형 안전을 위한 스트리퍼 스테이션의 장거리 디지털 레이저 센서를 포함합니다. 공압 회로에 대한 안전 규칙은 다음과 같습니다:

  • 가압된 라인을 절대 열지 마십시오. 유지보수 전에 감압하고 잠금 장치를 적용하십시오.
  • 리시버 및 고압 회로에 안전 밸브를 장착하고 시험합니다.
  • 블로우 스테이션을 파열 파편으로부터 보호하십시오. 가드가 열리면 라이트 커튼이 사이클을 중지시킵니다.
  • 호스, 밸브 및 피팅을 일정에 따라 점검하고 유지보수 계획에 따라 교체합니다.
  • 비상 정지 및 압력 알람의 의미에 대해 작업자를 교육합니다.

품질 검증 방법

압력 레시피는 그 뒤에 있는 검증만큼만 신뢰할 수 있습니다. 새로운 레시피나 재료 변경마다 다음 점검을 수행하십시오:

  • 구역별 벽 두께: 두께 게이지로 바닥, 몸체, 숄더, 넥을 측정하고 분포가 설계와 일치하는지 확인하십시오.
  • 용량: 병이 명시된 용량을 충족하는지 채워서 확인합니다.
  • 상부 하중: 적층 강도를 확인하기 위해 수직 하중을 가합니다.
  • 파열 압력: 충전 압력 이상의 안전 여유를 확인하기 위해 파열될 때까지 가압합니다.
  • 외관: 응력 자국, 헤이즈, 플래시 및 디테일 선명도를 확인합니다.
  • 첫 제품 및 배치 샘플링: 첫 제품을 완전히 검증한 후, 가동 중 설정된 간격으로 샘플링하십시오.

상대적 비용 및 에너지 프로파일

병을 생산하는 비용은 재료, 에너지, 스크랩이 지배합니다. 아래 표는 Aibim IBM 라인에서 재료별 일반적인 비용 및 에너지 등급을 평가합니다. 등급은 100 기준선을 참조하는 지수 포인트와 함께 낮음, 중간, 높음, 매우 높음, 프리미엄 밴드를 사용합니다.

Material Material Cost Band Energy Index Air Cost Band Process Difficulty
HDPE / LDPELow90LowLow
PPLow95LowMedium
PSMedium100MediumMedium
ABSMedium105MediumLow
SANMedium108MediumMedium
PETMedium110MediumMedium
PCTGHigh112MediumHigh
TPUHigh115HighHigh
PCVery High130HighVery High

에너지 지수는 IBM65에서 표준 PP 병에 대한 100점 기준선을 기준으로 합니다. PC는 건조 및 따뜻한 금형 요구로 인해 더 높습니다. 이 수치는 구매 가격이 아니며 상대적 운전 비용만을 나타냅니다.

Aibim 사출 블로우 성형기

Aibim은 각각 프리블로우와 파이널 블로우를 위한 제어식 공압 시스템을 갖춘 세 가지 핵심 IBM 시리즈를 제작합니다. 아래 사양 범위는 일반적인 엔지니어링 윈도우입니다. 금형과 재료에 대한 정확한 수치는 공장 데이터시트로 확인하십시오.

IBM75 사출 블로우 성형기

Parameter Typical Range
ModelIBM75
Injection screw diameter (mm)45
Shot size (g)80–150
Clamping force (kN)750
Container volume (ml)50–1000
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–16 + 20–40
Installed power (kW)25–33
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)10–16

IBM65 사출 블로우 성형기

Parameter Typical Range
ModelIBM65
Injection screw diameter (mm)40
Shot size (g)60–110
Clamping force (kN)650
Container volume (ml)10–500
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–16 + 20–40
Installed power (kW)18–25
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)9–14

IBM55 하이브리드 전동 사출 블로우 성형기

Parameter Typical Range
ModelIBM55 Hybrid Electric
Injection screw diameter (mm)35
Shot size (g)40–80
Clamping force (kN)550
Container volume (ml)3–250
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–14 + 18–36
Installed power (kW)12–18 (hybrid, lower draw)
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)8–13

All three series share the PREFILL hydraulic technology and variable displacement pump pressurizing system, the SD card parameter storage for cross-machine recipe reuse, and the single-crossbeam double-pole clamping framework that enlarges mold setting space. The IBM55 hybrid adds electric servo motion for lower energy draw on small containers.

응용 산업 및 재료 적합성

Aibim IBM 기계는 제약, 식품, 음료 및 화장품 산업에 사용됩니다. 압력 레시피는 내용물에 따라 결정됩니다:

  • 제약: PE, PP, PS, PC로 만든 경구용 액제, 점안액, 진단용 병은 깨끗하고 응력이 없는 부품이 필요합니다. 저압의 부드러운 램프가 약물 접촉 표면을 보호합니다.
  • 식품: PP 및 HDPE로 만든 소스, 꿀, 조미료 병은 견고한 넥(neck)이 필요합니다. 밀봉 무결성을 위해 압력을 조정합니다.
  • 음료: PET 및 PCTG 물병과 기능성 음료병은 투명성과 강도를 위해 배향이 필요합니다.
  • 화장품: ABS 및 SAN 크림 용기, TPU 소프트 튜브, PET 또는 PCTG 투명 용기는 표면 광택과 디테일이 필요합니다. 마감 품질에 맞춰 압력을 설정합니다.

Aibim 제품군에서 가공 가능한 재료는 PE(HDPE, LDPE, LLDPE), PP, PS, ABS, SAN, TPU, PC 및 PCTG입니다.

선택 가이드: 요구 사항에서 모델까지

이 표를 사용하여 요구 사항을 기계 및 공기 구성에 매핑하십시오. 범위는 참고용입니다. 최종 선택은 금형 캐비티 수와 생산량 목표에 따라 달라집니다.

Material Container Volume Wall / Output Recommended Model Air Config
PET / PCTG100–1000 mlMedium, high clarityIBM758–16 + 25–40 bar
PP / HDPE50–500 mlMedium, food gradeIBM656–12 + 20–34 bar
PS / SAN10–250 mlThin, glossyIBM55 Hybrid6–13 + 18–32 bar
PC50–500 mlThick, medicalIBM7510–18 + 30–45 bar
ABS10–500 mlMedium, opaqueIBM657–13 + 22–36 bar
TPU3–250 mlSoft, elasticIBM55 Hybrid4–9 + 14–26 bar
Small pharma3–100 mlHigh volumeIBM55 Hybrid6–14 + 18–36 bar

서비스 및 지원

Aibim, as a Wanplas factory, applies the Wanplas group service commitments. Before shipment each machine is test-run and inspected with the customer, CE certified with light curtain and laser sensor safety. Our engineers perform on-site installation and commissioning, and train your operators on pressure tuning and recipe storage.

The Wanplas shared policy provides USD 500 free parts per year and free replacement of damaged parts within the warranty period. Because recipes are stored on an SD card, a verified pressure setting can be carried to a second machine, which makes process transfer and capacity expansion straightforward. We also offer remote operation support, open our factory for customer visits, and guarantee transportation, production capacity, and quality standards.

자주 묻는 질문(FAQ)

프리블로우와 최종 블로우 압력의 차이는 무엇인가요?

프리블로우는 팽창을 시작하고 벽 분포를 설정하는 저압 단계이며, 파이널 블로우는 캐비티 접촉을 완료하고 디테일을 형성하는 고압 단계입니다. 먼저 프리블로우를 튜닝하면 두께를 제어할 수 있고, 그다음 파이널 블로우가 형상을 확보합니다.

사출 블로우 몰딩에서 재료가 블로우 압력에 어떤 영향을 미치나요?

각 재료는 점도와 냉각 속도가 다릅니다. 연질 PE는 저압이 필요하고, 경질 PC는 고압과 따뜻한 금형이 필요하며, 취성 PS는 부드러운 램프가 필요합니다. 이 가이드의 재료 표는 각각의 윈도우를 제공합니다.

PET와 PP에 동일한 블로우 압력을 사용할 수 있습니까?

아니요. PET는 배향을 형성하는 프리블로우와 25~40bar의 파이널 블로우가 필요하며, PP는 더 부드러운 램프와 결정화를 제어하는 금형 온도가 필요합니다. PP에 PET 레시피를 사용하면 응력 자국이 발생하고, PET에 PP 레시피를 사용하면 배향 불량과 헤이즈가 발생합니다.

왜 병이 적당한 압력에서도 터질까요?

파열은 일반적으로 너무 가파른 압력 램프, 차가운 재료 또는 잘못된 프리블로우 타이밍으로 인한 얇은 국부 벽에서 발생합니다. 파이널 블로우를 낮추거나 램프를 부드럽게 하고, 온도를 약간 올리고, 압력을 높이기 전에 프리블로우 지연을 확인하십시오.

새 병 설계에 맞게 블로우 압력을 어떻게 조정하나요?

6단계 방법을 따르십시오: 먼저 온도를 설정하고, 버블 형상을 위해 프리블로우를 설정하고, 접촉을 위해 파이널 블로우를 설정하고, 타이밍을 다듬고, 벽과 파열을 검증한 후 SD 카드에 저장합니다. 파이널 블로우 윈도우의 하한에서 시작하여 완전한 접촉이 될 때까지만 증가시킵니다.

더 높은 블로우 압력이 더 나은 병 품질을 의미하나요?

아니요. 접촉에 필요한 최소값 이상의 압력은 공기만 낭비하고 금형 마모를 증가시키며 응력, 파열, 헤이즈를 유발할 수 있습니다. 목표는 완전하고 균일한 캐비티 접촉을 주는 최저 압력입니다.

Aibim의 공압 시스템은 어떻게 에너지를 절약합니까?

Aibim은 유압 회로에 PREFILL 기술과 가변 용량 펌프를 사용하고 블로우용 단계식 고저 공기 시스템을 사용합니다. 이 조합은 기존 유압 라인 대비 최소 35%의 에너지 사용을 절감하며, 단계식 공기는 모든 것을 최대 압력으로 가동하는 것을 피합니다.

블로우 몰딩에 필요한 압축 공기 품질은 무엇인가요?

식품, 제약, 화장품 병의 경우 공기는 무오일이어야 하며 ISO 8573-1 개념에 부합하는 청정 등급으로 건조되어야 합니다. 청정 공기는 제품 안전을 보호하고 압력 안정성을 방해하는 밸브 내 오일 축적을 방지합니다.

결론

Blow pressure is not one number but a two-stage system of preblow and final blow, shaped by material, temperature, timing, and bottle geometry. The material table, shape-correction rules, tuning flow, and defect card in this guide give you a repeatable method to find the minimum pressure that delivers full cavity contact and a sound bottle. Aibim, a Wanplas factory, builds IBM75, IBM65, and IBM55 Hybrid machines with PREFILL technology, staged air, and SD-card recipe storage that make this method easy to apply and transfer across lines.

If you are qualifying a new material or bottle, send us your material grade and bottle drawing. We will prepare a material-specific pressure process package and a machine configuration suggestion, and we welcome you to send samples for trial molding and to visit our factory for machine inspection and test runs. Our team will help you lock in a verified, energy-efficient pressure recipe before you scale production.