İçindekiler
- Üfleme Basıncı Neden Tek Bir Sayı Değil, Bir Sistemdir
- Şişe Oluşumunda Üfleme Basıncının Fiziği
- İki Kademeli Basınç Sistemi: Ön Üfleme ve Son Üfleme
- Üfleme Basıncı Sıcaklık, Zamanlama ve Kalıpla Nasıl Etkileşir
- Malzemeye Göre Optimum Üfleme Basıncı Ayarları
- Şişe Şekline ve Cidar Kalınlığına Göre Basınç Düzeltmesi
- Adım Adım Basınç Ayarlama Metodolojisi
- Basınçla İlgili Kusurlar: Belirti ve Ayarlama Hızlı Referansı
- Pnömatik Sistem ve Enerji Verimliliği
- Yüksek Basınçlı Hava Sistemlerinin Güvenliği
- Kalite Doğrulama Yöntemleri
- Göreli Maliyet ve Enerji Profili
- Aibim Enjeksiyon Üfleme Kalıplama Makineleri
- Uygulama Endüstrileri ve Malzeme Uygunluğu
- Seçim Rehberi: İhtiyaçtan Modele
- Hizmet ve Destek
- Sıkça Sorulan Sorular
- Sonuç
Üfleme Basıncı Neden Tek Bir Sayı Değil, Bir Sistemdir
Aibim, a Wanplas factory based in Zhangjiagang, has manufactured injection (stretch) blow molding machines for more than 12 years, with 20 years of accumulated know-how in the injection blow molding field. Our lines serve customers in over 40 countries, run from our own CNC machining center, and produce more than 100 lines per year from a new factory established in 2022. Container sizes span from 3 ml medical droppers to 1000 ml cosmetic and food bottles. The single most misunderstood parameter among new operators is blow pressure. Many buyers ask for “the right blow pressure” as if it were one number printed on a dial. In reality, blow pressure is a system. It is the combination of a low-pressure preblow stage and a high-pressure final blow stage, multiplied by timing, material behavior, parison or preform temperature, mold temperature, and bottle geometry.
This guide explains blow pressure as a controllable process window rather than a fixed setpoint. We cover the physics of gas pressure pushing molten polymer against a cold mold cavity, the two-stage pressure architecture used on Aibim three-station one-step IBM machines, how pressure interacts with temperature and timing, and a full material-by-material table of optimal pressure windows. Whether you run PET, PP, PE, PS, SAN, PC, ABS, or TPU, the methodology below lets you move from a generic starting point to a verified, repeatable pressure recipe stored on the machine’s SD card.
Key Statistics
– Aibim: 12+ years of machine manufacturing, 20 years in injection blow molding know-how
– Exported to 40+ countries; 100+ lines per year capacity
– Container range 3 ml to 1000 ml; three-station one-step IBM process
– PREFILL hydraulic technology saves a minimum of 35% energy versus conventional hydraulic lines
– CE certified with light curtain and laser sensor safety systems
Şişe Oluşumunda Üfleme Basıncının Fiziği
Blow pressure exists for one physical purpose: to drive the molten polymer of the parison or preform outward until it contacts every surface of the blow mold cavity, then to hold it there while it freezes and takes the final shape. In injection blow molding the parison is injected as a tubular blank at the first station, transferred to the blow station, and expanded by compressed air. The air pressure does mechanical work against the polymer’s viscosity and against the heat-transfer rate of the mold wall.
When blow pressure is too low, the polymer cannot overcome its own viscosity and the mold’s cooling effect before it solidifies. The result is poor mold contact, shallow detail, thick-and-thin wall distribution, and weak structural zones. When blow pressure is too high, the polymer is forced into a thin, over-stretched skin that loses mechanical strength, develops internal stress, risks burst during the cycle, accelerates mold wear, and wastes compressed-air energy. The correct pressure is therefore a balance point where the material fully contacts the cavity with the minimum air energy required.
Air pressure also interacts with the rate of pressure rise. A steep, instant step from zero to maximum pressure can trap the material unevenly and create localized stress marks, while a controlled ramp that begins with a gentle preblow and rises to final blow gives the material time to distribute before it sets. This is why a two-stage system outperforms a single fixed pressure for bottles with non-uniform geometry.
The pressure required to move the polymer is a function of its extensional viscosity at the moment of blowing. A polymer that is still hot and soft extends at low pressure; the same polymer a few seconds later, after the mold has pulled heat from its surface, may need double the pressure to move the same distance and will instead tear or thin. This is the central reason blow pressure cannot be set without also controlling temperature and time. The operator is, in effect, racing the freeze front: pressure must arrive while the material is still mobile enough to flow, but not so early or so hard that it stretches the wrong zone.
Another physical factor is the surface area the air must push against. As the bubble grows, its internal volume rises with the cube of the radius while the wall area rises with the square, so the local stress in the wall drops as the bottle expands, provided the material keeps thinning evenly. If the pressure is too low, the bubble stalls before it reaches the cavity corners and the wall freezes in a thick, uneven state. If the pressure is too high, the bubble reaches the wall so fast that the material has no time to redistribute, producing a thin spot opposite the injection point and a thick ring near the neck. Reading the wall-thickness profile after a trial shot tells you far more about the correct pressure than the pressure gauge alone.
İki Kademeli Basınç Sistemi: Ön Üfleme ve Son Üfleme
Aibim IBM makinelerinde pnömatik devre iki kontrollü aşamaya ayrılmıştır. Her aşamanın rolünü anlamak, doğru ayarın temelidir.
Ön Şişirme Basıncı (Düşük Basınç Aşaması)
The preblow stage applies a low air pressure the moment the parison or preform enters the blow mold. Its job is to begin the expansion, establish the initial bubble shape, and guide where the material will go before the high pressure arrives. Preblow pressure and preblow timing together decide the wall-thickness distribution more than any other single variable. If the preblow is too weak or arrives too late, the material collapses onto the mold base before it has spread upward, leaving a thick bottom and a thin shoulder. If the preblow is too strong or arrives too early, the material stretches prematurely and thins in the zone that still needs material later.
Malzemeye göre tipik ön şişirme pencereleri aşağıdaki malzeme tablosunda ayrıntılıdır, ancak bir kavram olarak PET veya PCTG gibi yönlendirilmiş malzemeler için ön şişirme genellikle 8 ila 16 bar civarındayken, LDPE veya TPU gibi yumuşak malzemeler 4 ila 9 bar'a daha yakındır.
Son Şişirme Basıncı (Yüksek Basınç Aşaması)
The final blow stage applies the high pressure that completes cavity contact, forms fine detail such as embossing or threads, and sets the bottle dimensions. Final blow pressure is held for a defined dwell, then vented. For PET the final blow commonly ranges 25 to 40 bar; for PP, PE, PS, and PC the windows differ and are listed per material. After the high-pressure dwell, a short exhaust and cooling phase lets the part solidify enough for transfer to the ejection station.
Enjeksiyon Şişirme Kalıplama Farkı
In IBM the parison is injection-molded with precise wall distribution, then blown in a separate station on the same machine. Compared with extrusion blow molding, where the parison is extruded and hotter with more sag, IBM parisons are cooler and more controlled, so the blow pressure requirement is steadier and the scrap rate lower. Compared with two-step stretch blow molding of PET, IBM performs the blow on a preform that was just injected rather than re-heated, which removes the reheat oven variable but still requires correct blow pressure and timing for full orientation.
Üfleme Basıncı Sıcaklık, Zamanlama ve Kalıpla Nasıl Etkileşir
Şişirme basıncı asla tek başına ayarlanmaz. Basınç, sıcaklık ve zamanlamadan oluşan bir üçgene aittir. Bir kenarı değiştirmek diğerlerini de değişmeye zorlar.
- Sıcaklık bağlantısı: Daha sıcak bir parison veya preform daha düşük basınçta akar. Silindir veya kalıp sıcaklığını yükseltirseniz, şişirme basıncını genellikle düşürebilir ve yine de tam temas elde edebilirsiniz. Daha soğuk bir parça daha fazla basınç gerektirir, ancak soğuk malzemeye çok fazla basınç uygulamak gerilim ve patlama riski oluşturur.
- Zamanlama bağlantısı: Ön şişirme gecikmesi ve son şişirme bekleme süresi zamanlama kollarıdır. Gecikmiş bir ön şişirme malzemeyi aşağı kaydırır; daha uzun bir son bekleme süresi detayı iyileştirir ancak çevrimi ve enerji kullanımını uzatır.
- Kalıp sıcaklığı bağlantısı: Kalıp sıcaklığı donma hızını kontrol eder. Soğuk bir kalıp, keskin detay için daha yüksek basınç kullanmanıza izin verir ancak gerilim riski taşır; PP gibi kristalleşebilir malzemeler için sıcak bir kalıp kristalleşmeyi kontrol eder ancak sarkmayı önlemek için ayarlanmış basınç gerektirir.
- Sıkma kuvveti bağlantısı: Şişirme basıncı, iç göz yüzeyine karşı etki eder. Yeterli sıkma kuvveti, ayırma hattında çapak oluşumunu önler. Yeterli sıkma kuvveti olmadan şişirme basıncını artırmak, daha iyi şişeler yerine çapak üretir.
Pratik kural: Önce sıcaklık penceresini ayarlayın, ardından dağılımı ayarlamak için ön şişirmeyi, temas için son şişirmeyi ve sonra zamanlamayı düzeltin. Sıcaklığı ve zamanlamayı göz ardı ederek yalnızca basınç değerini değiştirerek asla bir kusuru kovalamayın.
Parison Duvar Tasarımı ve Şişirme Basıncına Etkisi
In injection blow molding the parison is not a neutral tube; its wall thickness profile is set at the injection station and directly determines how much blow pressure is needed and where. A parison with a heavier base and lighter shoulder will need less final blow pressure at the bottom and more at the top. A parison with uniform wall needs a more uniform pressure ramp. Because the parison wall is programmable through the injection and core-rod design, the blow pressure window is really the second half of a two-part control system: injection sets the material budget, blow pressure spends it.
This coupling means a pressure problem is sometimes solved at the injection end rather than the blow end. If a bottle consistently shows a thin shoulder regardless of final blow pressure, the parison is likely too light at the shoulder and no amount of air will move material that is not there. Adding parison weight at that zone, or shifting the core-rod program, reduces the required blow pressure and improves the result. Conversely, an over-heavy parison forces you to raise pressure merely to spread excess material, which wastes energy and stresses the mold. Treating parison design and blow pressure as one loop is the fastest route to a stable recipe.
Germe Çubuğu Etkileşimi
On machines that include a stretch step, the stretch rod physically lengthens the preform before the air arrives. The rod sets the axial orientation; the blow pressure sets the radial orientation. If the rod moves too far before the preblow, the material is already thin axially and the final blow will over-thin the side wall. If the rod moves too late, the preblow alone must do the axial work and will need a higher pressure than the material tolerates. The pressure recipe therefore includes the stretch rod speed and start point as hidden variables, especially for PET and PCTG where biaxial orientation defines quality.
Malzemeye Göre Optimum Üfleme Basıncı Ayarları
The table below gives engineering windows for each material processed on Aibim IBM machines. These are typical starting ranges, not guaranteed setpoints; always verify on the actual mold and material grade, and store the confirmed recipe on the SD card. Process temperature is the melt temperature in the barrel; mold temperature is the blow cavity temperature; hold time is the final-blow dwell.
Read the table as a band, not a point. Within each band, the correct value depends on wall thickness, bottle size, and cavity count. A thicker-wall bottle sits at the lower edge of the final-blow band because the material has more mass to push but less distance to travel; a thin-wall large bottle sits higher because the air must drive a light shell fully into a large cavity before it freezes. When moving between grades of the same polymer, raise the pressure slightly for higher molecular weight or higher filler content, and lower it for easier-flow grades. The per-material notes that follow explain the behavior behind each band so you can reason about adjustments instead of guessing.
| Material | Process Temp (°C) | Preblow (bar) | Final Blow (bar) | Hold Time (s) | Mold Temp (°C) | Typical Defect Linkage |
|---|---|---|---|---|---|---|
| PET | 260–285 | 8–16 | 25–40 | 1.5–3.0 | 10–25 | Low orientation if preblow weak; haze if over-pressured |
| PCTG | 255–280 | 8–15 | 24–38 | 2.0–3.5 | 20–40 | Stress marks if cooled too fast |
| PP (clarified) | 220–260 | 6–12 | 20–34 | 2.0–4.0 | 20–60 | White stress marks if pressure ramps too fast |
| HDPE | 200–230 | 5–10 | 16–30 | 2.0–4.0 | 10–40 | Softness; needs good cooling before eject |
| LDPE / LLDPE | 180–220 | 4–9 | 14–26 | 2.0–4.0 | 10–40 | Low rebound; risk of sticking |
| PS | 200–240 | 6–12 | 18–30 | 1.5–3.0 | 20–50 | Brittle; bursts if final blow too high |
| SAN | 210–250 | 7–13 | 20–32 | 2.0–3.5 | 40–70 | Needs warm mold for gloss; sensitive to over-pressure |
| PC | 280–320 | 10–18 | 30–45 | 3.0–6.0 | 80–120 | High dry requirement; stress cracks if over-pressured |
| ABS | 210–250 | 7–13 | 22–36 | 2.5–4.5 | 50–80 | Opaque; tolerant, medium pressure |
| TPU | 190–230 | 4–9 | 14–26 | 3.0–6.0 | 20–60 | Soft elastic; sticking and rebound control needed |
PET ve PCTG
PET and PCTG are orientation-sensitive. PET must be dried below about 50 ppm moisture before processing, and the preblow establishes the biaxial orientation that gives the bottle its strength and clarity. A weak preblow leaves the material un-oriented and cloudy; a correct preblow followed by a 25–40 bar final blow gives a clear, strong bottle. PCTG is less moisture-sensitive than PET but still benefits from a controlled ramp; over-pressure on a fast-cooling cavity produces stress whitening rather than crisp detail.
PP
PP is crystallizable and temperature-sensitive. Clarified PP for transparent bottles needs a warm enough mold to control crystallization, yet too warm a mold causes sag that must be countered by adjusting pressure timing rather than by raising pressure blindly. A gentle pressure ramp reduces the white stress marks common in PP. The window of 6–12 bar preblow and 20–34 bar final blow suits most PP bottles.
PE (HDPE, LDPE, LLDPE)
Polyethylene is soft and has low rebound, so it needs relatively low blow pressure. HDPE suits 16–30 bar final blow; LDPE and LLDPE need even less because they are more flexible and tend to stick to the cavity. Cooling and demolding control matter more than raw pressure for PE. Over-pressuring PE wastes air and can flash at the parting line without improving the bottle.
PS ve SAN
PS is intrinsically transparent but brittle. Final blow above the material’s comfort band causes burst or micro-cracks. A gentle, well-timed pressure rise is essential. SAN is similar but more chemical-resistant and glossy; it wants a warmer mold (40–70 °C) for surface gloss and a moderate pressure that does not over-stress the part.
PC
PC has high viscosity and demands high drying (below about 50 ppm) plus high process temperature (280–320 °C) and a warm mold (80–120 °C) to avoid stress. Blow pressure is among the highest of the common materials, 30–45 bar final, but the pressure must rise smoothly to avoid internal stress cracking. PC bottles are usually for medical or reusable drinkware where dimensional stability is critical.
ABS
ABS opak, dayanıklı ve affedicidir. Orta basınç (22–36 bar son) yeterlidir. Renk ve yüzey kaplamasının berraklıktan daha önemli olduğu kozmetik ve kişisel bakım kavanozları için seçilir. Normal kurutmanın ötesinde özel bir kurutma gerekmez ve kalıp, iyi bir yüzey için sıcak çalıştırılabilir.
TPU
TPU yumuşak ve elastiktir. Düşük basınç (14–26 bar son) ve dikkatli kalıptan çıkarma gerektirir çünkü elastik hafıza yapışma ve geri tepmeye neden olabilir. Çıkarma öncesi daha uzun bekleme ve soğutma deformasyonu azaltır. TPU şişeler, özel tıbbi ve yumuşak dokunuşlu kozmetik uygulamalarında görülür.
Şişe Şekline ve Cidar Kalınlığına Göre Basınç Düzeltmesi
Yuvarlak 100 ml'lik bir şişe için çalışan bir basınç reçetesi, kulplu 750 ml'lik asimetrik bir şişede başarısız olabilir. Aşağıdaki tablo, malzeme temel penceresinin üzerine uygulayacağınız düzeltme kurallarını verir.
| Bottle Type | Preblow Correction | Final Blow Correction | Timing Note |
|---|---|---|---|
| Thin wall (≤ 0.4 mm) | Slightly higher to avoid early contact | High, for full cavity contact | Shorten high-pressure dwell to limit thinning |
| Thick wall (≥ 1.2 mm) | Lower and later | Extend dwell and hold | Longer hold for complete freeze |
| Large volume (> 500 ml) | Lower, delayed preblow | Extend final dwell | Manage cooling, watch cycle time |
| Small volume (< 50 ml) | Higher preblow | Moderate final | Fast cycle, short dwell |
| Handle or asymmetric | Zone-balanced | Higher at fill stage for handle | Delay to fill recessed zones |
| Wide mouth | Lower preblow | Moderate final | Watch neck finish |
| Narrow neck | Moderate | Ensure base fills first | Confirm base before neck pressure |
Adım Adım Basınç Ayarlama Metodolojisi
Yeni bir malzeme, yeni bir kalıp veya yeni bir şişe boyutu başlattığınızda aşağıdaki karar akışını kullanın. Akış, basınç, sıcaklık ve zamanlamayı doğru sırada tutar.
| Step | Action | Set / Adjust | Verify |
|---|---|---|---|
| 1 | Fix material temperature window | Barrel and mold temp per material table | Melt flows, no degradation |
| 2 | Set preblow to form bubble | Preblow bar and delay per material | Even early expansion, no collapse |
| 3 | Set final blow for contact | Final blow bar and ramp rate | Full cavity contact, detail formed |
| 4 | Fine-tune timing | Preblow delay, final dwell, exhaust | Wall distribution balanced |
| 5 | Validate the part | Measure wall, volume, burst, top load | Within spec; no stress marks |
| 6 | Save and reuse | Store recipe on SD card | Same recipe runs on sister machines |
Son şişirme penceresinin alt ucundan başlayın ve yalnızca tam göz teması sağlanana kadar artırın. Minimumun üzerindeki her artış, israf edilmiş basınçlı hava enerjisidir. Kabul edilen değerleri belgeleyin; böylece reçete, sıfırdan yeniden ayarlanmadan başka bir IBM65 veya IBM75'e yeniden yüklenebilir.
Basınçla İlgili Kusurlar: Belirti ve Ayarlama Hızlı Referansı
Aşağıdaki tablo, yaygın şişirme kusurlarını basınçla ilgili ayar yönüyle eşleştirir. Bunu bir ilk müdahale kartı olarak değerlendirin; her zaman sıcaklık ve zamanlama kontrolleriyle doğrulayın.
| # | Symptom | Likely Pressure Cause | Adjustment Direction |
|---|---|---|---|
| 1 | Poor mold contact / incomplete forming | Final blow too low or delayed | Raise final blow; check preblow timing |
| 2 | Thin wall in shoulder or side | Preblow too early/strong, uneven parison | Lower or delay preblow; adjust parison temp |
| 3 | Thick wall / material pooling at base | Preblow too late, final too low | Advance preblow; raise final blow |
| 4 | Bottle burst during cycle | Final blow too high or ramp too steep | Lower final blow; soften ramp |
| 5 | White stress marks (PP/PE) | Pressure ramp too fast, cold material | Reduce pressure rate; raise temp |
| 6 | Flash at parting line | Final blow exceeds clamping force | Lower final blow; verify clamping force |
| 7 | Neck or finish deformation | Local over-pressure at neck | Reduce blow at neck; check mold temp |
| 8 | Unstable base / rocking | Preblow timing wrong, base not set | Adjust preblow timing; lower final slightly |
| 9 | Poor detail / embossing unclear | Final blow too low or dwell short | Raise final blow; extend dwell |
| 10 | Internal stress cracking (PC/PS) | Over-pressure, fast cooling | Lower pressure; raise mold temp; anneal |
| 11 | Ovality / distortion after eject | Pressure-cooling imbalance | Balance pressure with cooling time |
| 12 | Weld line at handle | Insufficient fill-stage pressure | Raise final at handle stage; adjust parison |
| 13 | Surface haze from over-pressure | Final blow too high for material | Reduce final blow |
| 14 | Short shot / incomplete fill | Air volume or final blow insufficient | Raise final blow; check air supply volume |
| 15 | Pinch-off too thin / leak | Clamping and pressure mismatch | Verify clamping; tune pressure |
| 16 | Residual pressure trap | Exhaust timing too late | Advance exhaust; check valve |
Yaygın Basınç Ayarı Hataları
Deneyimli operatörler bile yukarıdaki yöntemin önlemek için tasarlandığı birkaç hatayı tekrarlar. Bunları fark etmek ayar süresini kısaltır.
- Sıcaklıktan önce basıncı ayarlamak: Yanlış silindir veya kalıp sıcaklığında hiçbir basınç değeri anlamlı değildir. Önce sıcaklığı düzeltin.
- Tek bir kusuru daha fazla basınçla kovalamak: İnce bir omuz nadiren son şişirmeyi artırarak düzeltilir; parison ağırlığı veya ön şişirme zamanlamasıyla düzeltilir. Daha fazla basınç sorunu sadece başka yere taşır.
- Malzemeler arasında tek reçete kullanmak: PET ve PP birbirinin yerine geçemez; reçete, reçine sınıfıyla birlikte değişmelidir.
- Rampa hızını göz ardı etmek: Tepe değeri, ne kadar hızlı ulaşıldığından daha az önemlidir. Yumuşak bir rampa, patlama ve gerilim izlerini önler.
- Reçeteyi kaydetmemek: SD karttaki doğrulanmış bir reçete, malzeme ve şişeye göre saklanıp etiketlenmezse kayıp bilgidir.
- Güvenlik payı için aşırı basınç uygulamak: Minimumun üzerindeki %20'lik basınç payı nadiren işe yarar ve her zaman hava israfına yol açar, kalıbı aşındırır.
Pnömatik Sistem ve Enerji Verimliliği
Compressed air is one of the largest hidden costs in blow molding. Aibim machines use PREFILL technology and a variable displacement pump pressurizing system in the hydraulic circuit, and a staged high-low pressure air system for the blow function. The energy-saving design reduces consumption by a minimum of 35% compared with conventional hydraulic lines.
Air quality matters. For food, pharmaceutical, and cosmetic bottles the compressed air should be oil-free and dried to a clean class consistent with ISO 8573-1 concepts (oil, water, and particle limits). Contaminated air leaves odors or particles in the bottle and can foul valves. A staged supply separates the low-pressure preblow line from the high-pressure final-blow line so the compressor does not run everything at maximum pressure.
Air recovery, where practical, captures vented blow air or recovers expansion energy, lowering the effective energy per bottle. Even without full recovery, right-sizing the receiver, stabilizing line pressure, and only using the minimum final blow needed already cut air cost substantially. The table below compares energy and air indices using a baseline of 100 index points.
| Configuration | Air Energy Index | Relative Cost | vs Baseline |
|---|---|---|---|
| Conventional fixed pump, single pressure | 135 | High | 1.35× baseline |
| Staged high-low air, no recovery | 110 | Medium | 1.10× baseline |
| Aibim PREFILL + variable pump + staged air | 65 | Low | 0.65× baseline (35% saved) |
| Above with air recovery add-on | 52 | Low | 0.52× baseline |
Yüksek Basınçlı Hava Sistemlerinin Güvenliği
Son şişirme basınçları 25–45 bara ulaşır ve basınçlı hava sistemleri gerçek tehlike taşır. Aibim makineleri CE sertifikalıdır ve kişisel güvenlik için bir ışık perdesi ile kalıp güvenliği için sıyırıcı istasyonunda uzun mesafeli dijital lazer sensör içerir. Pnömatik devre için güvenlik kuralları şunları içerir:
- Basınçlı bir hattı asla açmayın; bakımdan önce basıncı boşaltın ve kilitleyin.
- Alıcılara ve yüksek basınç devresine basınç tahliye vanaları takın ve test edin.
- Şişirme istasyonunu patlama parçalarına karşı koruyun; koruma açılırsa ışık perdesi çevrimi durdurur.
- Hortumları, vanaları ve bağlantı parçalarını programa göre inceleyin; bakım planına göre değiştirin.
- Operatörleri acil durdurma ve basınç alarmlarının anlamı konusunda eğitin.
Kalite Doğrulama Yöntemleri
Bir basınç reçetesi ancak arkasındaki doğrulama kadar iyidir. Her yeni reçete veya malzeme değişikliği için şu kontrolleri yapın:
- Bölgeye göre duvar kalınlığı: Taban, gövde, omuz ve boynu bir kalınlık ölçerle ölçün; dağılımın tasarımla eşleştiğini doğrulayın.
- Hacim: Şişenin beyan edilen kapasiteyi karşıladığını doğrulamak için doldurun.
- Üst yük: İstif mukavemetini doğrulamak için dikey yük uygulayın.
- Patlama basıncı: Dolum basıncının üzerinde güvenli bir marjı doğrulamak için arızaya kadar basınç uygulayın.
- Görünüm: Stres izleri, bulanıklık, çapak ve detay netliği kontrol edin.
- İlk parça ve parti numunesi: İlk parçayı tam olarak doğrulayın, ardından üretim sırasında belirlenen aralıklarla numune alın.
Göreli Maliyet ve Enerji Profili
Bir şişeyi çalıştırmanın maliyetine malzeme, enerji ve hurda hakimdir. Aşağıdaki tablo, Aibim IBM hatlarında malzemeye göre tipik maliyet ve enerji kademelerini derecelendirir. Derecelendirmeler, 100 taban çizgisine referanslı endeks puanlarıyla Düşük, Orta, Yüksek, Çok Yüksek ve Premium bantlarını kullanır.
| Material | Material Cost Band | Energy Index | Air Cost Band | Process Difficulty |
|---|---|---|---|---|
| HDPE / LDPE | Low | 90 | Low | Low |
| PP | Low | 95 | Low | Medium |
| PS | Medium | 100 | Medium | Medium |
| ABS | Medium | 105 | Medium | Low |
| SAN | Medium | 108 | Medium | Medium |
| PET | Medium | 110 | Medium | Medium |
| PCTG | High | 112 | Medium | High |
| TPU | High | 115 | High | High |
| PC | Very High | 130 | High | Very High |
Enerji endeksi, IBM65 üzerindeki standart bir PP şişesi için 100 puanlık bir taban çizgisine göredir; PC, kurutma ve sıcak kalıp talebi nedeniyle daha yüksektir. Bu rakamların hiçbiri satın alma fiyatı değildir; yalnızca göreli işletme maliyetini tanımlarlar.
Aibim Enjeksiyon Üfleme Kalıplama Makineleri
Aibim, her biri ön şişirme ve son şişirme için kontrollü bir pnömatik sisteme sahip üç temel IBM serisi üretir. Aşağıdaki spesifikasyon aralıkları tipik mühendislik pencereleridir; kalıbınız ve malzemeniz için kesin değerleri fabrika veri sayfasıyla doğrulayın.
IBM75 Enjeksiyon Üfleme Kalıplama Makinesi
| Parameter | Typical Range |
|---|---|
| Model | IBM75 |
| Injection screw diameter (mm) | 45 |
| Shot size (g) | 80–150 |
| Clamping force (kN) | 750 |
| Container volume (ml) | 50–1000 |
| Stations | 3 (injection, blow, eject) |
| Air config (preblow + final blow, bar) | 6–16 + 20–40 |
| Installed power (kW) | 25–33 |
| Air consumption | Staged high-low; tuned per recipe |
| Cycle time (s) | 10–16 |
IBM65 Enjeksiyon Üfleme Kalıplama Makinesi
| Parameter | Typical Range |
|---|---|
| Model | IBM65 |
| Injection screw diameter (mm) | 40 |
| Shot size (g) | 60–110 |
| Clamping force (kN) | 650 |
| Container volume (ml) | 10–500 |
| Stations | 3 (injection, blow, eject) |
| Air config (preblow + final blow, bar) | 6–16 + 20–40 |
| Installed power (kW) | 18–25 |
| Air consumption | Staged high-low; tuned per recipe |
| Cycle time (s) | 9–14 |
IBM55 Hibrit Elektrikli Enjeksiyon Üfleme Kalıplama Makinesi
| Parameter | Typical Range |
|---|---|
| Model | IBM55 Hybrid Electric |
| Injection screw diameter (mm) | 35 |
| Shot size (g) | 40–80 |
| Clamping force (kN) | 550 |
| Container volume (ml) | 3–250 |
| Stations | 3 (injection, blow, eject) |
| Air config (preblow + final blow, bar) | 6–14 + 18–36 |
| Installed power (kW) | 12–18 (hybrid, lower draw) |
| Air consumption | Staged high-low; tuned per recipe |
| Cycle time (s) | 8–13 |
All three series share the PREFILL hydraulic technology and variable displacement pump pressurizing system, the SD card parameter storage for cross-machine recipe reuse, and the single-crossbeam double-pole clamping framework that enlarges mold setting space. The IBM55 hybrid adds electric servo motion for lower energy draw on small containers.
Uygulama Endüstrileri ve Malzeme Uygunluğu
Aibim IBM makineleri ilaç, gıda, içecek ve kozmetik endüstrilerine hizmet eder. Basınç reçetesi içeriğe göre belirlenir:
- İlaç: PE, PP, PS ve PC'den oral sıvı, göz damlası ve teşhis şişeleri temiz ve gerilimsiz parçalar gerektirir; düşük basınçlı yumuşak rampalar ilaçla temas eden yüzeyleri korur.
- Gıda: PP ve HDPE'den sos, bal ve çeşni şişeleri güvenli boyun gerektirir; basınç, sızdırmazlık bütünlüğü için ayarlanır.
- İçecek: PET ve PCTG'deki su ve fonksiyonel içecek şişeleri berraklık ve mukavemet için oryantasyon gerektirir.
- Kozmetik: ABS ve SAN'dan krem kavanozları, TPU'dan yumuşak tüpler ve PET veya PCTG'den şeffaf kavanozlar yüzey parlaklığı ve detay gerektirir; basınç, yüzey kalitesi için ayarlanır.
Aibim serisi boyunca işlenebilir malzemeler PE (HDPE, LDPE, LLDPE), PP, PS, ABS, SAN, TPU, PC ve PCTG'dir.
Seçim Rehberi: İhtiyaçtan Modele
Bir gereksinimi makine ve hava konfigürasyonuna eşlemek için bu tabloyu kullanın. Aralıklar yol göstericidir; nihai seçim kalıp göz sayısına ve üretim hedefine bağlıdır.
| Material | Container Volume | Wall / Output | Recommended Model | Air Config |
|---|---|---|---|---|
| PET / PCTG | 100–1000 ml | Medium, high clarity | IBM75 | 8–16 + 25–40 bar |
| PP / HDPE | 50–500 ml | Medium, food grade | IBM65 | 6–12 + 20–34 bar |
| PS / SAN | 10–250 ml | Thin, glossy | IBM55 Hybrid | 6–13 + 18–32 bar |
| PC | 50–500 ml | Thick, medical | IBM75 | 10–18 + 30–45 bar |
| ABS | 10–500 ml | Medium, opaque | IBM65 | 7–13 + 22–36 bar |
| TPU | 3–250 ml | Soft, elastic | IBM55 Hybrid | 4–9 + 14–26 bar |
| Small pharma | 3–100 ml | High volume | IBM55 Hybrid | 6–14 + 18–36 bar |
Hizmet ve Destek
Aibim, as a Wanplas factory, applies the Wanplas group service commitments. Before shipment each machine is test-run and inspected with the customer, CE certified with light curtain and laser sensor safety. Our engineers perform on-site installation and commissioning, and train your operators on pressure tuning and recipe storage.
The Wanplas shared policy provides USD 500 free parts per year and free replacement of damaged parts within the warranty period. Because recipes are stored on an SD card, a verified pressure setting can be carried to a second machine, which makes process transfer and capacity expansion straightforward. We also offer remote operation support, open our factory for customer visits, and guarantee transportation, production capacity, and quality standards.
Sıkça Sorulan Sorular
Ön şişirme ve son şişirme basıncı arasındaki fark nedir?
Ön şişirme, genleşmeyi başlatan ve duvar dağılımını belirleyen düşük basınç aşamasıdır; son şişirme, göz temasını tamamlayan ve detayı oluşturan yüksek basınç aşamasıdır. Önce ön şişirmeyi ayarlamak kalınlık üzerinde kontrol sağlar, ardından son şişirme şekli sabitler.
Malzeme enjeksiyon şişirme kalıplamada şişirme basıncını nasıl etkiler?
Her malzemenin farklı bir viskozitesi ve donma hızı vardır. Yumuşak PE düşük basınç gerektirir; sert PC yüksek basınç ve sıcak bir kalıp gerektirir; kırılgan PS nazik bir rampa gerektirir. Bu kılavuzdaki malzeme tablosu her biri için pencereyi verir.
PET ve PP için aynı şişirme basıncını kullanabilir miyim?
Hayır. PET, yönlenme oluşturan bir ön şişirme ve 25–40 bar son şişirme isterken, PP daha nazik bir rampa ve kristalleşmeyi kontrol eden bir kalıp sıcaklığı gerektirir. PP üzerinde PET reçetesi kullanmak gerilim izlerine neden olur; PET üzerinde PP reçetesi kullanmak zayıf yönlenme ve bulanıklık verir.
Şişem orta basınçta bile neden patlıyor?
Patlama genellikle çok dik bir basınç rampasından, soğuk malzemeden veya yanlış ön şişirme zamanlamasından kaynaklanan ince bir yerel duvardan gelir. Basıncı artırmadan önce son şişirmeyi düşürün veya rampayı yumuşatın, sıcaklığı hafifçe yükseltin ve ön şişirme gecikmesini kontrol edin.
Yeni bir şişe tasarımı için şişirme basıncını nasıl ayarlarım?
Altı adımlı yöntemi izleyin: önce sıcaklığı ayarlayın, kabarcık şekli için ön şişirmeyi ayarlayın, temas için son şişirmeyi ayarlayın, zamanlamayı düzeltin, duvarı ve patlamayı doğrulayın, ardından SD karta kaydedin. Son şişirme penceresinin alt ucundan başlayın ve yalnızca tam temas sağlanana kadar artırın.
Daha yüksek şişirme basıncı daha iyi şişe kalitesi anlamına mı gelir?
Hayır. Temas için gereken minimumun üzerindeki basınç yalnızca hava israfına yol açar, kalıp aşınmasını artırır ve gerilim, patlama ve bulanıklığa neden olabilir. Amaç, tam ve eşit göz teması sağlayan en düşük basınçtır.
Aibim'in pnömatik sistemi enerjiyi nasıl tasarruf eder?
Aibim, hidrolik devrede PREFILL teknolojisi ve değişken deplasmanlı pompa, ayrıca şişirme için kademeli yüksek-düşük hava sistemi kullanır. Bu kombinasyon, geleneksel hidrolik hatlara kıyasla enerji kullanımını minimum %35 azaltır ve kademeli hava, her şeyi maksimum basınçta çalıştırmayı önler.
Şişirme kalıplama için hangi basınçlı hava kalitesi gerekir?
Gıda, ilaç ve kozmetik şişeleri için hava, yağsız olmalı ve ISO 8573-1 kavramlarıyla uyumlu temiz bir sınıfa kadar kurutulmalıdır. Temiz hava, ürün güvenliğini korur ve basınç stabilitesini bozacak yağ birikiminden vanaları uzak tutar.
Sonuç
Blow pressure is not one number but a two-stage system of preblow and final blow, shaped by material, temperature, timing, and bottle geometry. The material table, shape-correction rules, tuning flow, and defect card in this guide give you a repeatable method to find the minimum pressure that delivers full cavity contact and a sound bottle. Aibim, a Wanplas factory, builds IBM75, IBM65, and IBM55 Hybrid machines with PREFILL technology, staged air, and SD-card recipe storage that make this method easy to apply and transfer across lines.
If you are qualifying a new material or bottle, send us your material grade and bottle drawing. We will prepare a material-specific pressure process package and a machine configuration suggestion, and we welcome you to send samples for trial molding and to visit our factory for machine inspection and test runs. Our team will help you lock in a verified, energy-efficient pressure recipe before you scale production.






