Running an injection blow molding line around the clock is no longer an exception reserved for the largest pharmaceutical and personal-care groups. For bottle makers that supply sterile pharmaceutical containers, oral syrup bottles, cosmetic essence bottles, and food condiment bottles under long-term contracts, 24/7 operation has become the normal way to recover equipment cost and meet steady demand. Aibim, a Wanplas factory with more than 12 years of experience in plastic machinery and two decades focused on injection blow molding, builds three-station, one-step IBM machines in the volume range from 3 ml to 1000 ml that are engineered for exactly this duty. This article explains what continuous production truly demands, how Aibim machines achieve running stability, and how a disciplined preventive maintenance schedule keeps them running for years without major unplanned stops.

The core idea is simple to state and hard to execute: stability is not a feature you buy once, it is a system you operate every shift. Enjeksiyon blow molding combines an injection stage that forms the preform, a transfer stage, and a blow stage that expands the preform against a chilled cavity in a single automatic sequence. Because there is no flash, no scrap parison, and no post-mold trimming, the IBM process is inherently clean and repeatable, which is why it fits sterile and high-clarity bottle programs so well. But that same closed loop only stays profitable when the machine, the mold, the auxiliary systems, and the people around them are all maintained on a planned calendar. The pages that follow give plant managers, maintenance leads, and production engineers a complete framework for running Aibim IBM lines seven days a week.

7/24 Sürekli Üretim IBM Makineleri için Ne Anlama Gelir ve Nerede Uygulanır

Continuous production means the machine runs through all available hours except for planned stops, and those planned stops are themselves scheduled, recorded, and minimized. It is not the same as simply leaving a machine switched on. A true 24/7 program on an injection blow molding line assumes three shifts, a material supply that never runs dry, a packing and downstream buffer that never backs up, and a maintenance plan that converts most failures into predicted, calendar-based service events. When these conditions are met, an Aibim IBM line can deliver a utilization in the high 90 percent range, with the only lost time being the short windows for mold changes, grade changes, and the highest-tier service items.

The best-fit scenarios are surprisingly narrow, and that is a good thing. Continuous running pays off when a single product or a small family of products is ordered in large, repeatable volume with little variation. Pharmaceutical bottle programs are the classic case: a hospital-supply manufacturer may need the same 60 ml HDPE pill bottle or the same 100 ml PETG diagnostic bottle for years, with forecasts that change slowly. Daily-chemical makers running a stable 30 ml essence bottle or a 50 ml lotion bottle for a global brand also fit. Gıda condiment producers with a constant 200 ml sauce bottle program are another strong fit. In each case the mold stays mounted for months, the material grade is fixed, and the line becomes a utility that simply converts resin into finished bottles at a known rate.

Continuous running is the wrong choice for a job shop that changes bottle shape every few days. Every mold change costs setup time and the risk of first-piece scrap, so a low-mix, high-volume profile is what makes 24/7 economics work. The table below contrasts the two operating profiles so a plant can decide whether the continuous model fits its order book before committing to the maintenance discipline this article describes.

IBM Hatlarında Sürekli Çalıştırma ile Parti Çalıştırma

Operating Factor	24/7 Continuous Profile	Batch or Single-Shift Profile
Order pattern	Stable, long contracts, low mix	Frequent changeovers, many SKUs
Mold mounted time	Months per setup	Days or weeks per setup
Maintenance model	Calendar-based, predictive	Run-to-failure tolerated
İşgücü need	Three shifts, technician rotating	One or two shifts
Cost recovery speed	Fast, high utilization	Slower, idle hours dominate
Best fit industry	Pharma, daily chemical, food	Custom packaging, trial runs

The decision to run continuously should be made with the maintenance plan already in hand, because the plan is what protects the return on the machine. Aibim supports this decision with its own CNC center for spare parts, a 100+ lines per year production capacity, and export experience to more than 40 countries, so the supply of machines and parts behind a 24/7 program is itself steady. The next sections explain the engineering that keeps each running hour reliable.

Stabilite Mühendisliği: Kesintisiz IBM Çalışmasının Dört Sütunu

Stable 24/7 output from an injection blow molding machine rests on four independent engineering pillars: mechanical rigidity, thermal stability of the hydraulic and servo systems, temperature-control accuracy, and control-system immunity to electrical interference. If any one pillar is weak, the line will drift, and drift during continuous running accumulates into scrap, cycle-time loss, and eventually a forced stop. Aibim designs each IBM model around all four pillars at once rather than treating them as separate upgrades.

Sütun Bir: Sıkma Çerçevesinin Mekanik Sertliği

The clamping unit is where rigidity matters most. During the blow stage the cavity must hold a precise shape against internal air pressure while the preform is expanded, and during ejection the part must release cleanly. Aibim uses a single-crossbeam, double-pole clamping framework with enlarged mold-setting space. This geometry resists the deflection that causes wall-thickness variation and flash at the parting line. Tie bars, platens, and the crossbeam are sized so that under rated clamping force the platen deflection stays small even after months of continuous cycling. When the frame is rigid, the mold seats repeatably, the preform transfers without distortion, and the finished bottle neck finish stays within tolerance batch after batch.

İkinci Temel: Hidrolik ve Servo Termal Kararlılık

Hydraulic and servo systems generate heat, and heat is the enemy of repeatability. Aibim IBM machines apply PREFILL technology together with a variable displacement pump pressurizing system in the hydraulic circuit. The variable displacement pump delivers flow only when the process demands it, which cuts the continuous energy loss that a fixed pump would dump as heat into the oil. Lower oil temperature means steadier viscosity, steadier injection speed, and a longer life for seals and valves. On the servo side, the drive and motor are sized with thermal margin and forced ventilation so that a 24/7 duty cycle does not push the inverter into thermal derating. Thermal stability is what lets the same shot weight repeat at 2 a.m. and at 2 p.m.

Üçüncü Sütun: Sıcaklık Kontrol Hassasiyeti

Enjeksiyon blow molding is a thermal process at every station. The barrel must plasticize the resin to a uniform melt with a controlled melt flow rate, the preform mold must set the parison at a temperature that still allows clean blow expansion, and the blow mold must chill the bottle quickly to hold clarity and shape. Aibim zones the barrel and the molds with independent closed-loop control, holding each zone near a setpoint with an accuracy on the order of plus or minus 1 degree Celsius. That tight band is what protects bottle weight consistency, neck dimensional stability, and surface gloss. In continuous running, the temperature loop must also reject disturbances from ambient swings and from the heat of neighboring zones, which is why zone isolation and good cooling-water control matter as much as the controller itself.

Dördüncü Sütun: Kontrol Sistemi Bağışıklığı ve Parametre Taşınabilirliği

The fourth pillar is the control system that ties the others together. Aibim stores complete process recipes on an SD card, so a proven parameter set can be carried from one machine to another without re-tuning by hand. This protects stability during expansion: when a second or third line is added, the first line’s recipe is the seed for the next. The controller also manages the stripper station through a long-distance digital laser sensor for mold safety and a light curtain for personal safety, so the machine can keep running with operators working safely around it. Electrical noise from servo drives, nearby compressors, and plant power fluctuation is handled through filtered supplies, proper grounding, and isolated signal lines, which keeps the temperature and position loops immune to interference that would otherwise show up as random scrap.

Stabilite, birinin başlığı değil, dört sütunun toplamıdır. Sert bir çerçeve, serin bir hidrolik ve servo düzeni, sıkı bir sıcaklık bandı ve parazit bağışıklığı olan bir kontrolör, 7/24 bir IBM hattının kârlı kalması için aynı anda geçerli olmalıdır.

Sürekli Çalışma için Temel Bileşen Ömürleri ve MTBF Referansı

Mean time between failures, expressed here as running hours or months under a 24/7 load, is the planning backbone of any preventive program. The values below are representative planning figures for Aibim IBM machines running three shifts with the maintenance tiers described later in this article. They are not guarantees and will shift with material abrasiveness, cooling-water quality, and ambient conditions, but they give maintenance leads a calendar to work against. The practical use of an MTBF number is to schedule the replacement or inspection just before the expected wear point, so the part is changed on a planned stop rather than after it fails.

7/24 Görev Altında Temsili Bileşen Ömrü Tablosu

Component	Typical Life Under 24/7	Failure Mode at Wear	Planning Action
Screw and barrel set	18 to 30 months	Wear raises back pressure need, degrades plasticizing	Measure clearance at quarter tier; order ahead
Enjeksiyon cylinder seals	9 to 15 months	External weep, pressure loss	Keep seal kit; replace at half-year tier
Hydraulic oil	6 months to clean change	Contamination, varnish, valve stick	Sample monthly; replace at half-year
Servo drive cooling fan	12 to 24 months	Over-temperature derating, alarm	Spare fan on site; swap at year tier
Heating band and thermocouple	12 to 18 months	Open circuit, temperature drift	Spares stocked; calibrate at quarter tier
Mold guide pin and bushing	15 to 24 months	Misalignment, parting-line flash	Lube weekly; inspect at half-year
Ejector pin and stripper	15 to 24 months	Sticking, drag marks	Clean shift; refurbish at half-year
Clamp linkage bronze bush	18 to 30 months	Play, uneven clamping force	Re-grease half-year; replace at year

These numbers should be treated as a living record. The most mature plants keep a per-machine log that updates the real replacement date next to the plan, and over time the plan converges with reality. Aibim supplies the maintenance structure and the spare parts, while the plant owns the log. The combination is what turns a list of estimates into a dependable production calendar.

Önleyici Bakım Programı: Vardiyadan Yıllık Kademelere

The preventive maintenance schedule is the heart of this article and the single most important document for a 24/7 IBM program. It is organized into six tiers: shift, weekly, monthly, quarterly, half-year, and annual. Each tier lists the inspection item, the acceptance standard, the tool or method, the responsible person, and the record that must be made. The discipline of writing the record is what makes the plan real; a check that is not logged did not happen from an audit point of view. The same structure is applied identically across all Aibim IBM models so that a technician moving between an IBM55, an IBM65, and an IBM75 needs no new procedure.

Her 8 Saatte Bir Yapılan Vardiya Kademesi Kontrolleri

Tier	Inspection Item	Standard / Criterion	Tool / Method	Responsible	Record
Shift	Hydraulic oil temperature and level	Temp within band, level at mark	HMI readout, sight glass	Operator	Shift log
Shift	Cooling water temperature and flow	Setpoint plus or minus 2 C, flow steady	Thermometer, flow indicator	Operator	Shift log
Shift	Safety door and light curtain function	Stops cycle on open	Manual test	Operator	Shift log
Shift	Alarm and event history review	No active or repeated alarms	HMI alarm list	Operator	Shift log
Shift	First-piece inspection	Weight, neck, visual pass	Scale, gauge, visual	Operator or QC	QC sheet

Haftalık, Aylık ve Üç Aylık Katmanlar

Tier	Inspection Item	Standard / Criterion	Tool / Method	Responsible	Record
Weekly	Fastener torque recheck	At spec, no slack	Torque wrench	Technician	Weekly sheet
Weekly	Lubrication of lubrication points	Visible film, no excess	Grease gun	Technician	Weekly sheet
Weekly	Mold water line descaling	Flow restored	Descale solution, flush	Technician	Weekly sheet
Weekly	Cavity surface cleaning	No deposit, no scratch	Soft cloth, approved cleaner	Technician	Weekly sheet
Weekly	Sensor calibration check	Reads match reference	Reference gauge	Technician	Weekly sheet
Monthly	Hydraulic oil cleanliness	Within ISO 4406 / NAS grade	Patch test, lab or kit	Technician	Monthly report
Monthly	Electrical cabinet cleaning and terminals	No dust, no loose screw	Vacuum, screwdriver	Electrician	Monthly report
Monthly	Servo parameter backup	Backup saved off machine	SD card, PC	Electrician	Monthly report
Monthly	Air line filter drain	No water in bowl	Manual drain	Technician	Monthly report
Quarterly	Screw and barrel clearance	Within wear limit	Air gauge, feeler	Senior tech	Quarter report
Quarterly	Clamping force calibration	Within plus or minus a few percent	Hydraulic gauge, load cell	Senior tech	Quarter report
Quarterly	Temperature loop calibration	Zone matches reference	Surface probe	Senior tech	Quarter report
Quarterly	Vacuum and exhaust system	Pull steady, no block	Gauge, inspect line	Senior tech	Quarter report

Altı Aylık ve Yıllık Kademeler

Tier	Inspection Item	Standard / Criterion	Tool / Method	Responsible	Record
Half-year	Hydraulic oil replacement	New oil, flushed system	Pump, filter change	Technician	Hizmet record
Half-year	Guide and gearbox lubrication	Fresh grease, no contamination	Lube, inspect	Technician	Hizmet record
Half-year	Mold overhaul and refurbish	Within tolerance, polished	Bench, polish, measure	Mold tech	Hizmet record
Half-year	Safety interlock function test	All interlocks verified	Function test	Electrician	Hizmet record
Annual	Full machine accuracy recheck	Per acceptance spec	Full gauge set	Senior tech	Annual report
Annual	Spare parts inventory count	Stock matches plan	Stock list	Planner	Annual report
Annual	Enerji baseline review	kWh per thousand pieces set	Meter data	Planner	Annual report
Annual	Control firmware upgrade review	Decision logged	Review with supplier	Engineer	Annual report

The schedule works only when the plant assigns a clear owner to each tier and treats the record as a quality document. Aibim supplies the checklists in both paper and digital form, and because recipes travel on the SD card, the maintenance history can travel with the machine when a line is relocated or resold. The cadence above is the baseline; plants with exceptionally abrasive fills or poor water quality may tighten the oil and descaling intervals, which is exactly the kind of local adjustment the framework is built to absorb.

Durum İzleme ve Öngörücü Bakım

Preventive maintenance keeps failure off the calendar by acting on time. Predictive maintenance goes one step further: it watches the machine’s vital signs and acts when the trend, not the clock, says a part is wearing out. For a 24/7 IBM line, predictive tools are the difference between a planned two-hour stop and a sudden weekend breakdown. The good news is that most of the signals are already present in the machine and only need to be observed with intent.

Vibration analysis on the servo motor, the hydraulic pump, and the clamp linkage catches imbalance and bearing wear weeks before a hard failure. Oil analysis, beyond the monthly patch test, tracks particle count and additive depletion to confirm the exact right moment for the half-year oil change. Motor current signature analysis reads the load drawn by the plasticizing screw and the clamp; a creeping current at constant output is an early sign of barrel wear or rising friction. Temperature trending across zones and cooling loops exposes a fouling heat exchanger long before it forces a cycle-time penalty. The table below ranks these methods by the effort they need and the downtime they typically avoid, expressed in relative levels and lost hours rather than cost.

Çaba ve Faydaya Göre Sıralanan Öngörücü Yöntemler

Method	Implementation Effort	Downtime Avoided	Best Target
Temperature trending	Low	Medium, several hours	Barrel, mold, oil
Hydraulic oil analysis	Medium	Medium, half-day	Valves, pump, seals
Motor current signature	Medium	High, up to a day	Screw, clamp, servo
Vibration analysis	Medium	High, up to a day	Pump, motor, linkage
Remote data review	Low	Medium, several hours	Whole line

Aibim supports remote monitoring so that process data and alarm history can be reviewed from the service hub, which means a developing fault can be flagged and a corrective action planned into the next shift change instead of waiting for a stoppage. The combination of a fixed preventive calendar and a flexible predictive layer is what lets mature plants report year-over-year gains in availability without buying new hardware.

Yaygın Arıza Süresi Kök Nedenleri ve Hızlı Kurtarma

Even with a strong plan, stops happen, and the cost of a stop is set mostly by how fast the crew diagnoses and recovers. The table below is a working playbook for the most common 24/7 IBM faults. Each row gives the observable symptom, the quick judgment, the corrective action, and the typical recovery time in hours when the crew is trained and the spare is on hand. The goal is to convert a vague “machine stopped” into a timed, scripted response.

IBM Hatları için Duruş Süresi El Kitabı

Fault	Symptom	Judgment	Action	Recovery
Material degrade and carbon build	Black specks, burnt smell	Residence too long or too hot	Purge barrel, lower zone, clean screw	1 to 3 hours
Mold vent blocked	Short fill, silver streak	Gas trapped in cavity	Clean vent, check exhaust	0.5 to 2 hours
Temperature zone runaway	Over temp alarm, scorch	Thermocouple or SSR failed	Swap thermocouple or band	1 to 2 hours
Servo alarm	Drive fault, no motion	Over temp or overload	Cool fan, reset, check load	0.5 to 3 hours
Wet compressed air	Water marks, rust spots	Dryer or drain failed	Drain, repair dryer, blow off	0.5 to 2 hours
Ejection not smooth	Stuck part, drag mark	Pin wear or contamination	Clean, lube, swap pin	0.5 to 2 hours

The single biggest lever on recovery time is spare availability. Every fault above is measured in hours only because the right seal, thermocouple, pin, or fan is already on the shelf. If the plant waits for a long-lead item to be shipped, those same faults become multi-day events. That is why the spare-parts policy and inventory plan discussed later are not optional extras but part of the recovery time itself.

Sürekli Üretim için Kalıp Değişim Stratejisi

A 24/7 line is only as continuous as its slowest changeover. Even a stable product program eventually needs a mold change for a new bottle, a color change for a brand variant, or a material grade change for a different application. The objective of a changeover strategy is to move as much work as possible off the running clock, which is the core idea behind SMED, single-minute exchange of die. Applied to IBM, this means preparing everything that can be prepared before the machine is stopped.

The external work includes preheating the next mold to its setpoint, staging the tool cart, loading the new recipe onto the SD card, and confirming the material and downstream packing are ready. The internal work, done only while the machine is stopped, is the physical swap of the three-station mold set, the reconnect of water and air, and the first-piece confirmation. Trained crews routinely complete an IBM mold change in the 45 to 90 minute range, which fits inside a single shift handover so production is rarely lost across a full shift. Color changes on the same material are far faster: a barrel purge with the new color masterbatch can be done in minutes to an hour depending on contrast, and because IBM has no scrap parison, there is no regrind loop to contaminate.

The changeover also has a quality side. A new mold must be qualified with a first-piece check for weight, neck finish, wall distribution, and visual clarity before full-speed running resumes. Building this qualification into the changeover window, rather than discovering a defect an hour into production, protects the yield factor that the OEE math depends on. Aibim simplifies the qualification step because the process recipe is portable: the new mold’s proven parameters are loaded from the SD card, so the machine reaches stable output faster than a hand-tuned start.

IBM Hatları için OEE Dağılımı ve İyileştirme

Overall equipment effectiveness is the metric that tells a plant whether 24/7 running is actually productive. OEE equals availability multiplied by performance multiplied by quality. Each factor captures a different kind of loss, and the maintenance plan above targets all three at once. Understanding where the loss sits is the first step to reducing it.

OEE Faktörleri ve IBM Hatlarındaki Tipik Kayıpları

OEE Factor	Typical Loss on IBM Line	Improvement Action
Availability	Unplanned stops, long changeovers	Preventive tiers, SMED changeover
Performance	Cycle creep, micro-stops	Temp and clamp calibration, cooling care
Kalite	Flash, short fill, contamination	Mold upkeep, vent cleaning, purge plan

A newly commissioned IBM line often lands in the low 70 percent OEE range once real-world stops are counted. The same line under the full maintenance and changeover discipline described here typically climbs toward the mid 80 percent range, with world-class continuous lines reaching higher. The headline number matters less than the trend: a plant that watches OEE monthly and ties each dip to a maintenance action creates a feedback loop that compounds. Because Aibim machines hold process recipes on SD cards, adding a second and third line does not reset the learning curve, so the OEE of a multi-line cell improves faster than a single line alone.

Enerji Tüketimi ve Yedek Parça Envanteri

Continuous running magnifies every unit of energy and every missing part. Enerji is best tracked as specific consumption, the kilowatt-hours per thousand finished bottles, because that normalizes for bottle size and lets different molds be compared on one axis. Aibim IBM machines are built to save a minimum of 35 percent energy against conventional hydraulic designs, mainly through PREFILL technology and the variable displacement pump that avoid continuous relief-valve loss. Under 24/7 duty this saving is realized every hour, so the annual energy difference against an older machine is large even before counting the carbon benefit that some brand owners now require.

The energy baseline set at the annual tier is the reference. If specific consumption drifts upward without a product change, the usual causes are a fouled mold water line, a cooling tower losing efficiency, a hydraulic system running hotter than design, or a screw and barrel pair wearing past optimal clearance. Each of these is caught by the maintenance tiers, which is why energy and maintenance are the same conversation, not two.

Spare parts inventory is the other half of continuous readiness. The stock plan splits parts into three lead-time classes. High-runner consumables must be on the shelf at all times. Medium-lead parts are ordered on a forecast so they arrive before the planned service window. Long-lead items, such as a complete screw and barrel set or a servo drive module, are either pre-positioned at the Wanplas service hub or pre-ordered against the MTBF calendar so a failure never becomes a weeks-long wait. The table below is a starter inventory for one IBM line.

Tedarik Süresi Sınıfına Göre Yedek Parça Stok Planı

Lead-Time Class	Parts to Stock	Stock Level	Reorder Trigger
On-site, high runner	Seals, heater bands, thermocouples, ejector pins, filter elements, servo fan	High	Use one, order one
Medium lead	Mold guide pins, bronze bushes, sensors, relay modules	Medium	Quarterly review
Long lead	Screw and barrel set, servo drive, main pump	Low or hub-held	Pre-order by MTBF

The Wanplas shared policy of USD 500 free parts per year covers a meaningful slice of the high-runner consumables, which directly reduces the cost of keeping the on-site shelf full. Plants should treat the free-parts allowance as the base layer of the inventory plan and budget the long-lead pre-positions separately, because those are the items that protect against the rare but expensive stop.

Üç Vardiyalı Çalışma için Personel ve Vardiya Yönetimi

No machine runs itself for 8,760 hours a year. The people around an IBM line are the executable layer of the maintenance plan. A three-shift operation needs a skill matrix that maps each task to the role that owns it, a handover routine that passes state between shifts, and a first-line maintenance responsibility that catches small issues before they grow.

The skill matrix typically defines three levels. Level one operators run the machine, feed material, pack bottles, and perform the shift-tier checks. Level two technicians handle weekly and monthly tiers, basic fault recovery, and mold changes. Level three senior technicians and electricians own the quarterly, half-year, and annual tiers and the predictive program. Cross-training across levels means a night shift is never left without someone who can execute the downtime playbook, which is the real risk in 24/7 operation.

The handover record is short but non-negotiable: current output rate, any active alarm cleared in the shift, material lot in use, mold mounted, and open maintenance items. A good handover takes five minutes and prevents the classic failure where shift B does not know that shift A already saw a rising oil temperature. Aibim reinforces this with the HMI alarm history and recipe tracking, so the digital record backs up the written one. The responsibility areas are also物理 divided: each operator owns a zone of the line for cleanliness and first-line checks, which builds the habit that keeps the shift-tier items from being skipped.

Sürekli Çalışma için Üretilmiş Aibim IBM Makineleri

Aibim offers a focused IBM lineup that covers the 3 ml to 1000 ml bottle range across three models, each engineered for the continuous duty described above. All three are three-station, one-step machines that inject the preform, transfer it, and blow it in a single automatic cycle with no flash and no post-trim. The single-crossbeam double-pole clamping frame, the PREFILL hydraulic system, and the SD-card recipe portability are common across the family, so a plant can mix models on one floor and train one crew.

The specification values below are typical configuration parameters for each model class and should be confirmed against the final quotation for a specific bottle and cavitation. They are presented to help planners size lines and match models to volume and bottle size before a detailed discussion with the factory.

Aibim IBM75 Enjeksiyon Üfleme Kalıplama Makinesi

Specification	IBM75 Value
Clamping force	75 metric ton (about 735 kN)
Screw diameter	45 mm
Shot size (PS, theoretical)	285 g
Cavity number (typical)	Up to 8, depends on bottle
Theoretical capacity	Around 1800 pcs/h for a 50 ml PP bottle at 6 cavities
Applicable bottle volume	10 ml to 500 ml
Installed power	About 28 kW
Process stations	Three-station, one-step

IBM75, daha büyük bir preform ve daha geniş bir boyun gerektiren orta hacimli farmasötik ve günlük kimyasal şişeler için iş makinesidir. Daha yüksek sıkma kuvveti, küçük şişelerde daha büyük göz sayısını ve krem kavanozları ile takviye şişeleri gibi daha geniş ağızlı kaplarda istikrarlı duvar kontrolünü destekler.

Aibim IBM65 Enjeksiyon Üfleme Kalıplama Makinesi

Specification	IBM65 Value
Clamping force	65 metric ton (about 638 kN)
Screw diameter	40 mm
Shot size (PS, theoretical)	210 g
Cavity number (typical)	Up to 10, depends on bottle
Theoretical capacity	Around 2400 pcs/h for a 15 ml bottle at 8 cavities
Applicable bottle volume	3 ml to 250 ml
Installed power	About 22 kW
Process stations	Three-station, one-step

IBM65, küçük bir preform üzerindeki yüksek göz boşluğunun en iyi parça başına maliyeti sağladığı oral şurup şişeleri, damlalıklı şişeler ve küçük kozmetik esanslar için en yaygın tercihtir. Sıkma kuvveti ve enerji dengesi, tek bir yüksek hacimli SKU için özel 24/7 hücreye uygundur.

Aibim IBM55 Hibrit Elektrikli Enjeksiyon Üfleme Kalıplama Makinesi

Specification	IBM55 Value
Clamping force	55 metric ton (about 539 kN)
Screw diameter	35 mm
Shot size (PS, theoretical)	145 g
Cavity number (typical)	Up to 12, depends on bottle
Theoretical capacity	Around 3000 pcs/h for a 5 ml bottle at 10 cavities
Applicable bottle volume	3 ml to 150 ml
Installed power	About 16 kW (electric servo driven)
Process stations	Three-station, one-step, hybrid electric

The IBM55 Hybrid Electric adds servo-driven motion to the already efficient hydraulic design, pushing installed power and cycle energy lower still, which is attractive for plants with high electricity cost or strict carbon targets. It is the natural choice for very small bottles such as unit-dose containers, nasal spray reservoirs, and micro cosmetic samples where maximum cavitation is the path to lowest piece cost.

Aibim IBM Hatlarının Hizmet Verdiği Uygulama Endüstrileri

Aibim IBM makineleri dört temel uygulama alanına hizmet eder ve her biri 7/24 esasına göre iyi çalışan somut nihai ürünlere karşılık gelir. Temiz, çapaksız IBM prosesi, bu uygulamaları ölçekte güvenilir kılan şeydir.

In pharmaceutics, the lines produce oral solid-dose bottles in HDPE and PP, oral syrup bottles with controlled wall distribution, dropper bottles for liquid medicine, and diagnostic reagent bottles in PETG and PC where clarity and low extractables matter. In food, the machines make condiment bottles, sauce bottles, and honey and spread containers where a tight neck and clean surface support secure capping. In drink, they produce small shot and sample bottles and concentrated beverage vials. In cosmetics, they make essence bottles, serum bottles, cream jars, and lotion bottles where surface gloss and neck precision define brand perception. Because the same barrel and screw accept PE, PP, PS, ABS, SAN, TPU, PC, and PCTG, a plant can serve several of these markets from one machine family by scheduling material grades rather than buying separate lines.

Model Seçim Rehberi: Şişe Hacmi, Çıktı ve Malzeme

The fastest way to size a line is to start from the bottle volume, the required output in pieces per hour, and the material. The table below gives a starting recommendation using the real Aibim models. Final cavitation and output are confirmed by the factory after a bottle drawing and material sample are reviewed, but this guide removes the guesswork from a first inquiry.

Requirement to Model Recommendation

Bottle Volume	Target Output (pcs/h)	Typical Material	Recommended Model
3 ml to 30 ml	2500 to 3500	Pharmaceutical-grade PP, PE	IBM55 Hybrid Electric
15 ml to 100 ml	2000 to 2800	PP, HDPE, PETG	IBM65
50 ml to 250 ml	1500 to 2200	HDPE, PP, PC	IBM65 or IBM75
200 ml to 500 ml	1200 to 1800	HDPE, PP, PETG	IBM75
500 ml to 1000 ml	600 to 1200	HDPE, PP	IBM75 (wide-mouth config)
Any, low energy target	Per volume above	Any IBM-grade resin	IBM55 Hybrid Electric

When a program sits between two models, the deciding factor is usually cavitation and floor space rather than clamping force alone. Aibim engineers review the bottle drawing, the required annual volume, and the available utilities to confirm the final configuration, and because the models share a control philosophy, a plant can start on one model and add another later without relearning the platform.

Kesintisiz Üretim için Servis ve Destek

A 24/7 program is only as supported as its supplier. Aibim, as a Wanplas factory, backs each machine with a service structure designed for continuous duty. Before shipment, every line is run and tested so that the commissioning at the customer site is a confirmation rather than a debug session. Installation and commissioning are carried out by Aibim engineers who train the local crew on operation, the maintenance tiers, and the downtime playbook at the same time.

The Wanplas shared after-sales policy applies to every Aibim machine: USD 500 free parts per year, free replacement of damaged parts within warranty, and an open-factory policy that welcomes customer visits to inspect production and quality control. Remote support lets the service hub review process data and alarm history, which shortens the time from fault to fix. For continuous operations, the most valued element is the spare-parts policy combined with the pre-positioned long-lead items at the Wanplas service level, because that is what keeps a rare failure from becoming a long stop. Training is not a one-time event; Aibim recommends refresh sessions as the crew grows, so the skill matrix stays filled as the plant scales from one line to a cell.

Sıkça Sorulan Sorular

Sonuç

Continuous 24/7 production on an injection blow molding line is an engineering discipline, not a setting on a switch. Stability comes from four pillars working together: a rigid clamping frame, a cool hydraulic and servo train, a tight temperature band, and an interference-immune controller. Those pillars are protected by a preventive maintenance schedule that runs from the shift check to the annual accuracy recheck, supported by predictive monitoring and a trained three-shift crew. Aibim, a Wanplas factory with more than 12 years in plastic machinery and two decades in injection blow molding, builds the IBM55, IBM65, and IBM75 as three-station, one-step machines that carry this discipline in their design, from PREFILL hydraulics to SD-card recipe portability.

If your operation runs steady, high-volume bottle programs in pharma, food, drink, or cosmetics, the right next step is to share your bottle drawing, target output, and material with the Aibim team. We will confirm the model and cavitation, run the line under test before shipment, commission it on site, train your crew on the maintenance tiers, and keep you covered with the Wanplas shared service policy including USD 500 free parts per year. You are also welcome to visit the factory to review production and quality control in person. The goal is simple: a line that runs this year, next year, and the year after with planned stops you control and output you can forecast.