Macchina per lo stampaggio a iniezione e soffiaggio

Guida alla regolazione della pressione di soffiaggio: impostazioni ottimali per diversi materiali plastici

Indice

Perché la pressione di soffiaggio è un sistema, non un singolo numero

Aibim, a Wanplas factory based in Zhangjiagang, has manufactured injection (stretch) blow molding machines for more than 12 years, with 20 years of accumulated know-how in the injection blow molding field. Our lines serve customers in over 40 countries, run from our own CNC machining center, and produce more than 100 lines per year from a new factory established in 2022. Container sizes span from 3 ml medical droppers to 1000 ml cosmetic and food bottles. The single most misunderstood parameter among new operators is blow pressure. Many buyers ask for “the right blow pressure” as if it were one number printed on a dial. In reality, blow pressure is a system. It is the combination of a low-pressure preblow stage and a high-pressure final blow stage, multiplied by timing, material behavior, parison or preform temperature, mold temperature, and bottle geometry.

This guide explains blow pressure as a controllable process window rather than a fixed setpoint. We cover the physics of gas pressure pushing molten polymer against a cold mold cavity, the two-stage pressure architecture used on Aibim three-station one-step IBM machines, how pressure interacts with temperature and timing, and a full material-by-material table of optimal pressure windows. Whether you run PET, PP, PE, PS, SAN, PC, ABS, or TPU, the methodology below lets you move from a generic starting point to a verified, repeatable pressure recipe stored on the machine’s SD card.

Key Statistics
– Aibim: 12+ years of machine manufacturing, 20 years in injection blow molding know-how
– Exported to 40+ countries; 100+ lines per year capacity
– Container range 3 ml to 1000 ml; three-station one-step IBM process
– PREFILL hydraulic technology saves a minimum of 35% energy versus conventional hydraulic lines
– CE certified with light curtain and laser sensor safety systems

La fisica della pressione di soffiaggio nella formazione delle bottiglie

Blow pressure exists for one physical purpose: to drive the molten polymer of the parison or preform outward until it contacts every surface of the blow mold cavity, then to hold it there while it freezes and takes the final shape. In injection blow molding the parison is injected as a tubular blank at the first station, transferred to the blow station, and expanded by compressed air. The air pressure does mechanical work against the polymer’s viscosity and against the heat-transfer rate of the mold wall.

When blow pressure is too low, the polymer cannot overcome its own viscosity and the mold’s cooling effect before it solidifies. The result is poor mold contact, shallow detail, thick-and-thin wall distribution, and weak structural zones. When blow pressure is too high, the polymer is forced into a thin, over-stretched skin that loses mechanical strength, develops internal stress, risks burst during the cycle, accelerates mold wear, and wastes compressed-air energy. The correct pressure is therefore a balance point where the material fully contacts the cavity with the minimum air energy required.

Air pressure also interacts with the rate of pressure rise. A steep, instant step from zero to maximum pressure can trap the material unevenly and create localized stress marks, while a controlled ramp that begins with a gentle preblow and rises to final blow gives the material time to distribute before it sets. This is why a two-stage system outperforms a single fixed pressure for bottles with non-uniform geometry.

The pressure required to move the polymer is a function of its extensional viscosity at the moment of blowing. A polymer that is still hot and soft extends at low pressure; the same polymer a few seconds later, after the mold has pulled heat from its surface, may need double the pressure to move the same distance and will instead tear or thin. This is the central reason blow pressure cannot be set without also controlling temperature and time. The operator is, in effect, racing the freeze front: pressure must arrive while the material is still mobile enough to flow, but not so early or so hard that it stretches the wrong zone.

Another physical factor is the surface area the air must push against. As the bubble grows, its internal volume rises with the cube of the radius while the wall area rises with the square, so the local stress in the wall drops as the bottle expands, provided the material keeps thinning evenly. If the pressure is too low, the bubble stalls before it reaches the cavity corners and the wall freezes in a thick, uneven state. If the pressure is too high, the bubble reaches the wall so fast that the material has no time to redistribute, producing a thin spot opposite the injection point and a thick ring near the neck. Reading the wall-thickness profile after a trial shot tells you far more about the correct pressure than the pressure gauge alone.

Il sistema di pressione a due stadi: pre-soffiaggio e soffiaggio finale

Sulle macchine Aibim IBM il circuito pneumatico è suddiviso in due stadi controllati. Comprendere il ruolo di ciascuno stadio è la base di una corretta regolazione.

Pressione di pre-soffiaggio (fase a bassa pressione)

The preblow stage applies a low air pressure the moment the parison or preform enters the blow mold. Its job is to begin the expansion, establish the initial bubble shape, and guide where the material will go before the high pressure arrives. Preblow pressure and preblow timing together decide the wall-thickness distribution more than any other single variable. If the preblow is too weak or arrives too late, the material collapses onto the mold base before it has spread upward, leaving a thick bottom and a thin shoulder. If the preblow is too strong or arrives too early, the material stretches prematurely and thins in the zone that still needs material later.

Le finestre tipiche di pre-soffiaggio per materiale sono dettagliate nella tabella dei materiali di seguito, ma come concetto il pre-soffiaggio per materiali orientati come PET o PCTG si colloca spesso intorno a 8-16 bar, mentre materiali morbidi come LDPE o TPU si collocano più vicino a 4-9 bar.

Pressione di soffiaggio finale (fase ad alta pressione)

The final blow stage applies the high pressure that completes cavity contact, forms fine detail such as embossing or threads, and sets the bottle dimensions. Final blow pressure is held for a defined dwell, then vented. For PET the final blow commonly ranges 25 to 40 bar; for PP, PE, PS, and PC the windows differ and are listed per material. After the high-pressure dwell, a short exhaust and cooling phase lets the part solidify enough for transfer to the ejection station.

La differenza dello stampaggio a iniezione-soffiaggio

In IBM the parison is injection-molded with precise wall distribution, then blown in a separate station on the same machine. Compared with extrusion blow molding, where the parison is extruded and hotter with more sag, IBM parisons are cooler and more controlled, so the blow pressure requirement is steadier and the scrap rate lower. Compared with two-step stretch blow molding of PET, IBM performs the blow on a preform that was just injected rather than re-heated, which removes the reheat oven variable but still requires correct blow pressure and timing for full orientation.

Come la pressione di soffiaggio si combina con temperatura, tempi e stampo

La pressione di soffiaggio non viene mai regolata in modo isolato. Appartiene a un triangolo di pressione, temperatura e tempi. Modificare un lato impone una modifica degli altri.

  • Accoppiamento della temperatura: una parison o una preforma più calda scorre a pressione più bassa. Se si alza la temperatura di canna o stampo, spesso si può abbassare la pressione di soffiaggio ottenendo comunque il contatto completo. Un pezzo più freddo richiede più pressione, ma applicare troppa pressione su materiale freddo crea tensioni e rischio di scoppio.
  • Accoppiamento dei tempi: il ritardo del pre-soffiaggio e la pausa del soffiaggio finale sono leve temporali. Un pre-soffiaggio ritardato sposta il materiale verso il basso; una pausa finale più lunga migliora il dettaglio ma allunga il ciclo e il consumo energetico.
  • Accoppiamento della temperatura dello stampo: la temperatura dello stampo controlla la velocità di congelamento. Uno stampo freddo consente di usare pressione più alta per dettagli nitidi ma rischia tensioni; uno stampo caldo per materiali cristallizzabili come il PP controlla la cristallizzazione ma richiede una pressione regolata per evitare cedimenti.
  • Accoppiamento della forza di chiusura: la pressione di soffiaggio agisce contro la superficie interna della cavità. Una forza di chiusura adeguata previene le bave sulla linea di separazione. Aumentare la pressione di soffiaggio senza sufficiente forza di chiusura produce bave anziché bottiglie migliori.

La regola pratica: impostare prima la finestra di temperatura, poi il pre-soffiaggio per impostare la distribuzione, poi il soffiaggio finale per il contatto, quindi rifinire i tempi. Non inseguire mai un difetto modificando solo il valore di pressione ignorando temperatura e tempi.

Progettazione della parete della parison e suo effetto sulla pressione di soffiaggio

In injection blow molding the parison is not a neutral tube; its wall thickness profile is set at the injection station and directly determines how much blow pressure is needed and where. A parison with a heavier base and lighter shoulder will need less final blow pressure at the bottom and more at the top. A parison with uniform wall needs a more uniform pressure ramp. Because the parison wall is programmable through the injection and core-rod design, the blow pressure window is really the second half of a two-part control system: injection sets the material budget, blow pressure spends it.

This coupling means a pressure problem is sometimes solved at the injection end rather than the blow end. If a bottle consistently shows a thin shoulder regardless of final blow pressure, the parison is likely too light at the shoulder and no amount of air will move material that is not there. Adding parison weight at that zone, or shifting the core-rod program, reduces the required blow pressure and improves the result. Conversely, an over-heavy parison forces you to raise pressure merely to spread excess material, which wastes energy and stresses the mold. Treating parison design and blow pressure as one loop is the fastest route to a stable recipe.

Interazione dell'asta di stiro

On machines that include a stretch step, the stretch rod physically lengthens the preform before the air arrives. The rod sets the axial orientation; the blow pressure sets the radial orientation. If the rod moves too far before the preblow, the material is already thin axially and the final blow will over-thin the side wall. If the rod moves too late, the preblow alone must do the axial work and will need a higher pressure than the material tolerates. The pressure recipe therefore includes the stretch rod speed and start point as hidden variables, especially for PET and PCTG where biaxial orientation defines quality.

Impostazioni ottimali della pressione di soffiaggio per materiale

The table below gives engineering windows for each material processed on Aibim IBM machines. These are typical starting ranges, not guaranteed setpoints; always verify on the actual mold and material grade, and store the confirmed recipe on the SD card. Process temperature is the melt temperature in the barrel; mold temperature is the blow cavity temperature; hold time is the final-blow dwell.

Read the table as a band, not a point. Within each band, the correct value depends on wall thickness, bottle size, and cavity count. A thicker-wall bottle sits at the lower edge of the final-blow band because the material has more mass to push but less distance to travel; a thin-wall large bottle sits higher because the air must drive a light shell fully into a large cavity before it freezes. When moving between grades of the same polymer, raise the pressure slightly for higher molecular weight or higher filler content, and lower it for easier-flow grades. The per-material notes that follow explain the behavior behind each band so you can reason about adjustments instead of guessing.

Material Process Temp (°C) Preblow (bar) Final Blow (bar) Hold Time (s) Mold Temp (°C) Typical Defect Linkage
PET 260–285 8–16 25–40 1.5–3.0 10–25 Low orientation if preblow weak; haze if over-pressured
PCTG 255–280 8–15 24–38 2.0–3.5 20–40 Stress marks if cooled too fast
PP (clarified) 220–260 6–12 20–34 2.0–4.0 20–60 White stress marks if pressure ramps too fast
HDPE 200–230 5–10 16–30 2.0–4.0 10–40 Softness; needs good cooling before eject
LDPE / LLDPE 180–220 4–9 14–26 2.0–4.0 10–40 Low rebound; risk of sticking
PS 200–240 6–12 18–30 1.5–3.0 20–50 Brittle; bursts if final blow too high
SAN 210–250 7–13 20–32 2.0–3.5 40–70 Needs warm mold for gloss; sensitive to over-pressure
PC 280–320 10–18 30–45 3.0–6.0 80–120 High dry requirement; stress cracks if over-pressured
ABS 210–250 7–13 22–36 2.5–4.5 50–80 Opaque; tolerant, medium pressure
TPU 190–230 4–9 14–26 3.0–6.0 20–60 Soft elastic; sticking and rebound control needed

PET e PCTG

PET and PCTG are orientation-sensitive. PET must be dried below about 50 ppm moisture before processing, and the preblow establishes the biaxial orientation that gives the bottle its strength and clarity. A weak preblow leaves the material un-oriented and cloudy; a correct preblow followed by a 25–40 bar final blow gives a clear, strong bottle. PCTG is less moisture-sensitive than PET but still benefits from a controlled ramp; over-pressure on a fast-cooling cavity produces stress whitening rather than crisp detail.

PP

PP is crystallizable and temperature-sensitive. Clarified PP for transparent bottles needs a warm enough mold to control crystallization, yet too warm a mold causes sag that must be countered by adjusting pressure timing rather than by raising pressure blindly. A gentle pressure ramp reduces the white stress marks common in PP. The window of 6–12 bar preblow and 20–34 bar final blow suits most PP bottles.

PE (HDPE, LDPE, LLDPE)

Polyethylene is soft and has low rebound, so it needs relatively low blow pressure. HDPE suits 16–30 bar final blow; LDPE and LLDPE need even less because they are more flexible and tend to stick to the cavity. Cooling and demolding control matter more than raw pressure for PE. Over-pressuring PE wastes air and can flash at the parting line without improving the bottle.

PS e SAN

PS is intrinsically transparent but brittle. Final blow above the material’s comfort band causes burst or micro-cracks. A gentle, well-timed pressure rise is essential. SAN is similar but more chemical-resistant and glossy; it wants a warmer mold (40–70 °C) for surface gloss and a moderate pressure that does not over-stress the part.

PC

PC has high viscosity and demands high drying (below about 50 ppm) plus high process temperature (280–320 °C) and a warm mold (80–120 °C) to avoid stress. Blow pressure is among the highest of the common materials, 30–45 bar final, but the pressure must rise smoothly to avoid internal stress cracking. PC bottles are usually for medical or reusable drinkware where dimensional stability is critical.

ABS

L'ABS è opaco, resistente e tollerante. È sufficiente una pressione media (22-36 bar finali). Viene scelto per barattoli cosmetici e per la cura personale dove colore e finitura superficiale contano più della trasparenza. Non è richiesta un'essiccazione speciale oltre a quella normale e lo stampo può lavorare caldo per una buona superficie.

TPU

Il TPU è morbido ed elastico. Richiede bassa pressione (14-26 bar finali) e un'estrazione accurata perché la memoria elastica può causare adesione e ritorno elastico. Una pausa più lunga e un raffreddamento prima dell'espulsione riducono la deformazione. Le bottiglie in TPU compaiono in applicazioni mediche speciali e cosmetiche soft-touch.

Correzione della pressione in base alla forma della bottiglia e allo spessore della parete

Una ricetta di pressione che funziona per una bottiglia rotonda da 100 ml può fallire su una bottiglia asimmetrica da 750 ml con manico. La tabella seguente fornisce regole di correzione da applicare sopra la finestra base del materiale.

Bottle Type Preblow Correction Final Blow Correction Timing Note
Thin wall (≤ 0.4 mm) Slightly higher to avoid early contact High, for full cavity contact Shorten high-pressure dwell to limit thinning
Thick wall (≥ 1.2 mm) Lower and later Extend dwell and hold Longer hold for complete freeze
Large volume (> 500 ml) Lower, delayed preblow Extend final dwell Manage cooling, watch cycle time
Small volume (< 50 ml) Higher preblow Moderate final Fast cycle, short dwell
Handle or asymmetric Zone-balanced Higher at fill stage for handle Delay to fill recessed zones
Wide mouth Lower preblow Moderate final Watch neck finish
Narrow neck Moderate Ensure base fills first Confirm base before neck pressure

Metodologia di regolazione della pressione passo dopo passo

Usare il seguente flusso decisionale ogni volta che si avvia un nuovo materiale, un nuovo stampo o una nuova dimensione di bottiglia. Il flusso mantiene pressione, temperatura e tempi nell'ordine corretto.

>
Step Action Set / Adjust Verify
1 Fix material temperature window Barrel and mold temp per material table Melt flows, no degradation
2 Set preblow to form bubble Preblow bar and delay per material Even early expansion, no collapse
3 Set final blow for contact Final blow bar and ramp rate Full cavity contact, detail formed
4 Fine-tune timing Preblow delay, final dwell, exhaust Wall distribution balanced
5 Validate the part Measure wall, volume, burst, top load Within spec; no stress marks
6 Save and reuse Store recipe on SD card Same recipe runs on sister machines

Iniziare dall'estremità bassa della finestra del soffiaggio finale e aumentare solo fino al raggiungimento del contatto completo con la cavità. Ogni aumento oltre il minimo è energia di aria compressa sprecata. Documentare i valori accettati così la ricetta può essere ricaricata su un'altra IBM65 o IBM75 senza ri-regolare da zero.

Difetti legati alla pressione: riferimento rapido di sintomi e regolazioni

La tabella seguente associa i difetti di soffiaggio comuni alla direzione di regolazione legata alla pressione. Trattarla come una scheda di primo intervento; confermare sempre con i controlli di temperatura e tempi.

# Symptom Likely Pressure Cause Adjustment Direction
1Poor mold contact / incomplete formingFinal blow too low or delayedRaise final blow; check preblow timing
2Thin wall in shoulder or sidePreblow too early/strong, uneven parisonLower or delay preblow; adjust parison temp
3Thick wall / material pooling at basePreblow too late, final too lowAdvance preblow; raise final blow
4Bottle burst during cycleFinal blow too high or ramp too steepLower final blow; soften ramp
5White stress marks (PP/PE)Pressure ramp too fast, cold materialReduce pressure rate; raise temp
6Flash at parting lineFinal blow exceeds clamping forceLower final blow; verify clamping force
7Neck or finish deformationLocal over-pressure at neckReduce blow at neck; check mold temp
8Unstable base / rockingPreblow timing wrong, base not setAdjust preblow timing; lower final slightly
9Poor detail / embossing unclearFinal blow too low or dwell shortRaise final blow; extend dwell
10Internal stress cracking (PC/PS)Over-pressure, fast coolingLower pressure; raise mold temp; anneal
11Ovality / distortion after ejectPressure-cooling imbalanceBalance pressure with cooling time
12Weld line at handleInsufficient fill-stage pressureRaise final at handle stage; adjust parison
13Surface haze from over-pressureFinal blow too high for materialReduce final blow
14Short shot / incomplete fillAir volume or final blow insufficientRaise final blow; check air supply volume
15Pinch-off too thin / leakClamping and pressure mismatchVerify clamping; tune pressure
16Residual pressure trapExhaust timing too lateAdvance exhaust; check valve

Errori comuni nell'impostazione della pressione

Anche gli operatori esperti ripetono alcuni errori che il metodo sopra descritto è progettato per prevenire. Riconoscerli riduce i tempi di regolazione.

  • Impostare la pressione prima della temperatura: con la temperatura sbagliata di canna o stampo, qualsiasi valore di pressione è privo di significato. Correggere prima la temperatura.
  • Inseguire un difetto con più pressione: una spalla sottile raramente si corregge aumentando il soffiaggio finale; si corregge con il peso della parison o con i tempi del pre-soffiaggio. Più pressione sposta semplicemente il problema altrove.
  • Usare una sola ricetta per materiali diversi: PET e PP non sono intercambiabili; la ricetta deve cambiare con il grado di resina.
  • Ignorare la velocità di rampa: il valore di picco conta meno della rapidità con cui viene raggiunto. Una rampa morbida previene scoppi e segni da tensione.
  • Non salvare la ricetta: una ricetta verificata sulla scheda SD è conoscenza persa se non viene archiviata ed etichettata per materiale e bottiglia.
  • Sovrapressione per margine di sicurezza: un margine di pressione del 20% oltre il minimo raramente aiuta e spreca sempre aria e usura lo stampo.

Sistema pneumatico ed efficienza energetica

Compressed air is one of the largest hidden costs in blow molding. Aibim machines use PREFILL technology and a variable displacement pump pressurizing system in the hydraulic circuit, and a staged high-low pressure air system for the blow function. The energy-saving design reduces consumption by a minimum of 35% compared with conventional hydraulic lines.

Air quality matters. For food, pharmaceutical, and cosmetic bottles the compressed air should be oil-free and dried to a clean class consistent with ISO 8573-1 concepts (oil, water, and particle limits). Contaminated air leaves odors or particles in the bottle and can foul valves. A staged supply separates the low-pressure preblow line from the high-pressure final-blow line so the compressor does not run everything at maximum pressure.

Air recovery, where practical, captures vented blow air or recovers expansion energy, lowering the effective energy per bottle. Even without full recovery, right-sizing the receiver, stabilizing line pressure, and only using the minimum final blow needed already cut air cost substantially. The table below compares energy and air indices using a baseline of 100 index points.

Configuration Air Energy Index Relative Cost vs Baseline
Conventional fixed pump, single pressure135High1.35× baseline
Staged high-low air, no recovery110Medium1.10× baseline
Aibim PREFILL + variable pump + staged air65Low0.65× baseline (35% saved)
Above with air recovery add-on52Low0.52× baseline

Sicurezza dei sistemi ad aria ad alta pressione

Le pressioni del soffiaggio finale raggiungono 25-45 bar e i sistemi di aria compressa comportano un rischio reale. Le macchine Aibim sono certificate CE e includono una cortina di luce per la sicurezza del personale e un sensore laser digitale a lunga distanza alla stazione di estrazione per la sicurezza dello stampo. Le regole di sicurezza per il circuito pneumatico includono:

  • Non aprire mai una linea in pressione; depressurizzare e bloccare prima della manutenzione.
  • Installare e testare le valvole di sicurezza sui serbatoi e sul circuito ad alta pressione.
  • Proteggere la stazione di soffiaggio dai frammenti di scoppio; la cortina di luce arresta il ciclo se la protezione viene aperta.
  • Ispezionare tubi flessibili, valvole e raccordi secondo un programma; sostituire secondo il piano di manutenzione.
  • Formare gli operatori sull'arresto di emergenza e sul significato degli allarmi di pressione.

Metodi di verifica della qualità

Una ricetta di pressione vale quanto la verifica che la sostiene. Per ogni nuova ricetta o cambio di materiale, eseguire questi controlli:

  • Spessore della parete per zona: misurare fondo, corpo, spalla e collo con un calibro per spessori; confermare che la distribuzione corrisponda al progetto.
  • Volume: riempire per confermare che la bottiglia soddisfa la capacità dichiarata.
  • Carico di compressione: applicare un carico verticale per confermare la resistenza all'impilamento.
  • Pressione di scoppio: pressurizzare fino alla rottura per confermare un margine di sicurezza sopra la pressione di riempimento.
  • Aspetto: verificare la presenza di segni da stress, alone, bava e nitidezza dei dettagli.
  • Campionamento del primo pezzo e a lotti: qualificare completamente il primo pezzo, quindi campionare a intervalli prestabiliti durante la produzione.

Costo relativo e profilo energetico

Il costo di produzione di una bottiglia è dominato da materiale, energia e scarti. La tabella seguente valuta i livelli tipici di costo ed energia per materiale sulle linee Aibim IBM. Le valutazioni usano fasce Basso, Medio, Alto, Molto Alto e Premium con punti indice riferiti a una base di 100.

Material Material Cost Band Energy Index Air Cost Band Process Difficulty
HDPE / LDPELow90LowLow
PPLow95LowMedium
PSMedium100MediumMedium
ABSMedium105MediumLow
SANMedium108MediumMedium
PETMedium110MediumMedium
PCTGHigh112MediumHigh
TPUHigh115HighHigh
PCVery High130HighVery High

L'indice energetico è relativo a una base di 100 punti per una bottiglia standard in PP su una IBM65; il PC è più alto a causa dell'essiccazione e della richiesta di stampo caldo. Nessuna di queste cifre è un prezzo di acquisto; descrivono solo il costo di esercizio relativo.

Macchine per stampaggio a iniezione e soffiaggio Aibim

Aibim costruisce tre serie IBM principali, ciascuna con un sistema pneumatico controllato per pre-soffiaggio e soffiaggio finale. Gli intervalli di specifica di seguito sono finestre ingegneristiche tipiche; confermare i valori esatti con la scheda tecnica di fabbrica per il proprio stampo e materiale.

Macchina per stampaggio a iniezione e soffiaggio IBM75

Parameter Typical Range
ModelIBM75
Injection screw diameter (mm)45
Shot size (g)80–150
Clamping force (kN)750
Container volume (ml)50–1000
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–16 + 20–40
Installed power (kW)25–33
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)10–16

Macchina per stampaggio a iniezione e soffiaggio IBM65

Parameter Typical Range
ModelIBM65
Injection screw diameter (mm)40
Shot size (g)60–110
Clamping force (kN)650
Container volume (ml)10–500
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–16 + 20–40
Installed power (kW)18–25
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)9–14

Macchina per stampaggio a iniezione e soffiaggio ibrida elettrica IBM55

Parameter Typical Range
ModelIBM55 Hybrid Electric
Injection screw diameter (mm)35
Shot size (g)40–80
Clamping force (kN)550
Container volume (ml)3–250
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–14 + 18–36
Installed power (kW)12–18 (hybrid, lower draw)
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)8–13

All three series share the PREFILL hydraulic technology and variable displacement pump pressurizing system, the SD card parameter storage for cross-machine recipe reuse, and the single-crossbeam double-pole clamping framework that enlarges mold setting space. The IBM55 hybrid adds electric servo motion for lower energy draw on small containers.

Settori applicativi e idoneità dei materiali

Le macchine Aibim IBM servono i settori farmaceutico, alimentare, delle bevande e cosmetico. La ricetta di pressione segue il contenuto:

  • Farmaceutico: le bottiglie per liquidi orali, colliri e diagnostici in PE, PP, PS e PC richiedono parti pulite e prive di tensioni; rampe morbide a bassa pressione proteggono le superfici a contatto con il farmaco.
  • Alimentare: le bottiglie per salse, miele e condimenti in PP e HDPE richiedono colli sicuri; pressione calibrata per l'integrità della tenuta.
  • Bevande: le bottiglie per acqua e bevande funzionali in PET e PCTG richiedono l'orientamento per trasparenza e resistenza.
  • Cosmetico: i barattoli per creme in ABS e SAN, i tubetti morbidi in TPU e i barattoli trasparenti in PET o PCTG richiedono lucentezza e dettaglio superficiale; pressione impostata per la qualità della finitura.

I materiali lavorabili nell'intera gamma Aibim sono PE (HDPE, LDPE, LLDPE), PP, PS, ABS, SAN, TPU, PC e PCTG.

Guida alla selezione: dal requisito al modello

Usare questa tabella per associare un requisito a una macchina e a una configurazione dell'aria. Gli intervalli sono indicativi; la scelta finale dipende dalla cavitazione dello stampo e dall'obiettivo di produzione.

Material Container Volume Wall / Output Recommended Model Air Config
PET / PCTG100–1000 mlMedium, high clarityIBM758–16 + 25–40 bar
PP / HDPE50–500 mlMedium, food gradeIBM656–12 + 20–34 bar
PS / SAN10–250 mlThin, glossyIBM55 Hybrid6–13 + 18–32 bar
PC50–500 mlThick, medicalIBM7510–18 + 30–45 bar
ABS10–500 mlMedium, opaqueIBM657–13 + 22–36 bar
TPU3–250 mlSoft, elasticIBM55 Hybrid4–9 + 14–26 bar
Small pharma3–100 mlHigh volumeIBM55 Hybrid6–14 + 18–36 bar

Servizio e supporto

Aibim, as a Wanplas factory, applies the Wanplas group service commitments. Before shipment each machine is test-run and inspected with the customer, CE certified with light curtain and laser sensor safety. Our engineers perform on-site installation and commissioning, and train your operators on pressure tuning and recipe storage.

The Wanplas shared policy provides USD 500 free parts per year and free replacement of damaged parts within the warranty period. Because recipes are stored on an SD card, a verified pressure setting can be carried to a second machine, which makes process transfer and capacity expansion straightforward. We also offer remote operation support, open our factory for customer visits, and guarantee transportation, production capacity, and quality standards.

Domande frequenti

Qual è la differenza tra la pressione di pre-soffiaggio e quella di soffiaggio finale?

Il pre-soffiaggio è lo stadio a bassa pressione che avvia l'espansione e imposta la distribuzione della parete; il soffiaggio finale è lo stadio ad alta pressione che completa il contatto con la cavità e forma il dettaglio. Regolare prima il pre-soffiaggio dà controllo sullo spessore, poi il soffiaggio finale fissa la forma.

In che modo il materiale influisce sulla pressione di soffiaggio nello stampaggio a iniezione-soffiaggio?

Ogni materiale ha una viscosità e una velocità di congelamento diverse. Il PE morbido richiede bassa pressione; il PC rigido richiede alta pressione e uno stampo caldo; il PS fragile richiede una rampa dolce. La tabella dei materiali in questa guida fornisce la finestra per ciascuno.

Posso usare la stessa pressione di soffiaggio per PET e PP?

No. Il PET richiede un pre-soffiaggio che costruisca orientamento e un soffiaggio finale di 25-40 bar, mentre il PP richiede una rampa più dolce e una temperatura dello stampo che controlli la cristallizzazione. Usare una ricetta PET sul PP causa segni da tensione; usare una ricetta PP sul PET produce scarso orientamento e opacità.

Perché la mia bottiglia scoppia anche a pressione moderata?

Lo scoppio di solito deriva da una rampa di pressione troppo ripida, da materiale freddo o da una parete locale sottile dovuta a tempi di pre-soffiaggio errati. Abbassare il soffiaggio finale o ammorbidire la rampa, alzare leggermente la temperatura e controllare il ritardo del pre-soffiaggio prima di aumentare la pressione.

Come regolo la pressione di soffiaggio per un nuovo design di bottiglia?

Seguire il metodo in sei fasi: impostare prima la temperatura, impostare il pre-soffiaggio per la forma della bolla, impostare il soffiaggio finale per il contatto, rifinire i tempi, validare parete e scoppio, quindi salvare sulla scheda SD. Iniziare dall'estremità bassa della finestra del soffiaggio finale e aumentare solo fino al contatto completo.

Una pressione di soffiaggio più alta significa una migliore qualità della bottiglia?

No. La pressione superiore al minimo necessario per il contatto spreca solo aria, aumenta l'usura dello stampo e può causare tensioni, scoppi e opacità. L'obiettivo è la pressione più bassa che garantisce un contatto pieno e uniforme con la cavità.

Come fa il sistema pneumatico Aibim a risparmiare energia?

Aibim utilizza la tecnologia PREFILL e una pompa a cilindrata variabile nel circuito idraulico, oltre a un sistema aria alto-basso a stadi per il soffiaggio. Questa combinazione riduce il consumo energetico di almeno il 35% rispetto alle linee idrauliche convenzionali e l'aria a stadi evita di far funzionare tutto alla pressione massima.

Quale qualità dell'aria compressa è richiesta per lo stampaggio a soffiaggio?

Per le bottiglie alimentari, farmaceutiche e cosmetiche l'aria deve essere priva di olio ed essiccata a una classe di purezza allineata ai concetti ISO 8573-1. L'aria pulita protegge la sicurezza del prodotto e mantiene le valvole libere da accumuli di olio che disturberebbero la stabilità della pressione.

Conclusione

Blow pressure is not one number but a two-stage system of preblow and final blow, shaped by material, temperature, timing, and bottle geometry. The material table, shape-correction rules, tuning flow, and defect card in this guide give you a repeatable method to find the minimum pressure that delivers full cavity contact and a sound bottle. Aibim, a Wanplas factory, builds IBM75, IBM65, and IBM55 Hybrid machines with PREFILL technology, staged air, and SD-card recipe storage that make this method easy to apply and transfer across lines.

If you are qualifying a new material or bottle, send us your material grade and bottle drawing. We will prepare a material-specific pressure process package and a machine configuration suggestion, and we welcome you to send samples for trial molding and to visit our factory for machine inspection and test runs. Our team will help you lock in a verified, energy-efficient pressure recipe before you scale production.