Máquina de moldeo por inyección y soplado

Guía de ajuste de la presión de soplado: ajustes óptimos para diferentes materiales plásticos

Índice

Por qué la presión de soplado es un sistema, no un número único

Aibim, a Wanplas factory based in Zhangjiagang, has manufactured injection (stretch) blow molding machines for more than 12 years, with 20 years of accumulated know-how in the injection blow molding field. Our lines serve customers in over 40 countries, run from our own CNC machining center, and produce more than 100 lines per year from a new factory established in 2022. Container sizes span from 3 ml medical droppers to 1000 ml cosmetic and food bottles. The single most misunderstood parameter among new operators is blow pressure. Many buyers ask for “the right blow pressure” as if it were one number printed on a dial. In reality, blow pressure is a system. It is the combination of a low-pressure preblow stage and a high-pressure final blow stage, multiplied by timing, material behavior, parison or preform temperature, mold temperature, and bottle geometry.

This guide explains blow pressure as a controllable process window rather than a fixed setpoint. We cover the physics of gas pressure pushing molten polymer against a cold mold cavity, the two-stage pressure architecture used on Aibim three-station one-step IBM machines, how pressure interacts with temperature and timing, and a full material-by-material table of optimal pressure windows. Whether you run PET, PP, PE, PS, SAN, PC, ABS, or TPU, the methodology below lets you move from a generic starting point to a verified, repeatable pressure recipe stored on the machine’s SD card.

Key Statistics
– Aibim: 12+ years of machine manufacturing, 20 years in injection blow molding know-how
– Exported to 40+ countries; 100+ lines per year capacity
– Container range 3 ml to 1000 ml; three-station one-step IBM process
– PREFILL hydraulic technology saves a minimum of 35% energy versus conventional hydraulic lines
– CE certified with light curtain and laser sensor safety systems

La física de la presión de soplado en la formación de botellas

Blow pressure exists for one physical purpose: to drive the molten polymer of the parison or preform outward until it contacts every surface of the blow mold cavity, then to hold it there while it freezes and takes the final shape. In injection blow molding the parison is injected as a tubular blank at the first station, transferred to the blow station, and expanded by compressed air. The air pressure does mechanical work against the polymer’s viscosity and against the heat-transfer rate of the mold wall.

When blow pressure is too low, the polymer cannot overcome its own viscosity and the mold’s cooling effect before it solidifies. The result is poor mold contact, shallow detail, thick-and-thin wall distribution, and weak structural zones. When blow pressure is too high, the polymer is forced into a thin, over-stretched skin that loses mechanical strength, develops internal stress, risks burst during the cycle, accelerates mold wear, and wastes compressed-air energy. The correct pressure is therefore a balance point where the material fully contacts the cavity with the minimum air energy required.

Air pressure also interacts with the rate of pressure rise. A steep, instant step from zero to maximum pressure can trap the material unevenly and create localized stress marks, while a controlled ramp that begins with a gentle preblow and rises to final blow gives the material time to distribute before it sets. This is why a two-stage system outperforms a single fixed pressure for bottles with non-uniform geometry.

The pressure required to move the polymer is a function of its extensional viscosity at the moment of blowing. A polymer that is still hot and soft extends at low pressure; the same polymer a few seconds later, after the mold has pulled heat from its surface, may need double the pressure to move the same distance and will instead tear or thin. This is the central reason blow pressure cannot be set without also controlling temperature and time. The operator is, in effect, racing the freeze front: pressure must arrive while the material is still mobile enough to flow, but not so early or so hard that it stretches the wrong zone.

Another physical factor is the surface area the air must push against. As the bubble grows, its internal volume rises with the cube of the radius while the wall area rises with the square, so the local stress in the wall drops as the bottle expands, provided the material keeps thinning evenly. If the pressure is too low, the bubble stalls before it reaches the cavity corners and the wall freezes in a thick, uneven state. If the pressure is too high, the bubble reaches the wall so fast that the material has no time to redistribute, producing a thin spot opposite the injection point and a thick ring near the neck. Reading the wall-thickness profile after a trial shot tells you far more about the correct pressure than the pressure gauge alone.

El sistema de presión de dos etapas: pre-soplado y soplado final

En las máquinas Aibim IBM, el circuito neumático se divide en dos etapas controladas. Comprender el papel de cada etapa es la base de un ajuste correcto.

Presión de pre-soplado (etapa de baja presión)

The preblow stage applies a low air pressure the moment the parison or preform enters the blow mold. Its job is to begin the expansion, establish the initial bubble shape, and guide where the material will go before the high pressure arrives. Preblow pressure and preblow timing together decide the wall-thickness distribution more than any other single variable. If the preblow is too weak or arrives too late, the material collapses onto the mold base before it has spread upward, leaving a thick bottom and a thin shoulder. If the preblow is too strong or arrives too early, the material stretches prematurely and thins in the zone that still needs material later.

Las ventanas típicas de pre-soplado por material se detallan en la tabla de materiales siguiente, pero como concepto, el pre-soplado para materiales orientados como PET o PCTG suele situarse entre 8 y 16 bar, mientras que los materiales blandos como LDPE o TPU se sitúan más cerca de 4 a 9 bar.

Presión de soplado final (etapa de alta presión)

The final blow stage applies the high pressure that completes cavity contact, forms fine detail such as embossing or threads, and sets the bottle dimensions. Final blow pressure is held for a defined dwell, then vented. For PET the final blow commonly ranges 25 to 40 bar; for PP, PE, PS, and PC the windows differ and are listed per material. After the high-pressure dwell, a short exhaust and cooling phase lets the part solidify enough for transfer to the ejection station.

La diferencia del moldeo por soplado por inyección

In IBM the parison is injection-molded with precise wall distribution, then blown in a separate station on the same machine. Compared with extrusion blow molding, where the parison is extruded and hotter with more sag, IBM parisons are cooler and more controlled, so the blow pressure requirement is steadier and the scrap rate lower. Compared with two-step stretch blow molding of PET, IBM performs the blow on a preform that was just injected rather than re-heated, which removes the reheat oven variable but still requires correct blow pressure and timing for full orientation.

Cómo se acopla la presión de soplado con la temperatura, la sincronización y el molde

La presión de soplado nunca se ajusta de forma aislada. Pertenece a un triángulo de presión, temperatura y tiempo. Cambiar un lado obliga a cambiar los demás.

  • Acoplamiento de temperatura: un parisón o preforma más caliente fluye a menor presión. Si aumenta la temperatura del cilindro o del molde, a menudo puede bajar la presión de soplado y aun así lograr el contacto completo. Una pieza más fría necesita más presión, pero aplicar demasiada presión sobre material frío crea tensión y riesgo de explosión.
  • Acoplamiento de tiempos: el retardo del pre-soplado y el tiempo de mantenimiento del soplado final son palancas de tiempo. Un pre-soplado retardado desplaza el material hacia abajo; un mantenimiento final más largo mejora el detalle pero alarga el ciclo y el consumo de energía.
  • Acoplamiento de la temperatura del molde: la temperatura del molde controla la velocidad de congelación. Un molde frío permite usar mayor presión para un detalle nítido pero arriesga tensión; un molde caliente para materiales cristalizables como PP controla la cristalización pero necesita presión ajustada para evitar el pandeo.
  • Acoplamiento de la fuerza de cierre: la presión de soplado actúa contra la superficie interna de la cavidad. Una fuerza de cierre adecuada evita la rebaba en la línea de partición. Aumentar la presión de soplado sin suficiente fuerza de cierre produce rebaba en lugar de mejores botellas.

La regla práctica: ajuste primero la ventana de temperatura, luego el pre-soplado para establecer la distribución, luego el soplado final para el contacto, y finalmente recorte el tiempo. Nunca persiga un defecto moviendo solo el valor de presión mientras ignora la temperatura y el tiempo.

Diseño de la pared de la preforma y su efecto en la presión de soplado

In injection blow molding the parison is not a neutral tube; its wall thickness profile is set at the injection station and directly determines how much blow pressure is needed and where. A parison with a heavier base and lighter shoulder will need less final blow pressure at the bottom and more at the top. A parison with uniform wall needs a more uniform pressure ramp. Because the parison wall is programmable through the injection and core-rod design, the blow pressure window is really the second half of a two-part control system: injection sets the material budget, blow pressure spends it.

This coupling means a pressure problem is sometimes solved at the injection end rather than the blow end. If a bottle consistently shows a thin shoulder regardless of final blow pressure, the parison is likely too light at the shoulder and no amount of air will move material that is not there. Adding parison weight at that zone, or shifting the core-rod program, reduces the required blow pressure and improves the result. Conversely, an over-heavy parison forces you to raise pressure merely to spread excess material, which wastes energy and stresses the mold. Treating parison design and blow pressure as one loop is the fastest route to a stable recipe.

Interacción de la varilla de estirado

On machines that include a stretch step, the stretch rod physically lengthens the preform before the air arrives. The rod sets the axial orientation; the blow pressure sets the radial orientation. If the rod moves too far before the preblow, the material is already thin axially and the final blow will over-thin the side wall. If the rod moves too late, the preblow alone must do the axial work and will need a higher pressure than the material tolerates. The pressure recipe therefore includes the stretch rod speed and start point as hidden variables, especially for PET and PCTG where biaxial orientation defines quality.

Ajustes óptimos de presión de soplado según el material

The table below gives engineering windows for each material processed on Aibim IBM machines. These are typical starting ranges, not guaranteed setpoints; always verify on the actual mold and material grade, and store the confirmed recipe on the SD card. Process temperature is the melt temperature in the barrel; mold temperature is the blow cavity temperature; hold time is the final-blow dwell.

Read the table as a band, not a point. Within each band, the correct value depends on wall thickness, bottle size, and cavity count. A thicker-wall bottle sits at the lower edge of the final-blow band because the material has more mass to push but less distance to travel; a thin-wall large bottle sits higher because the air must drive a light shell fully into a large cavity before it freezes. When moving between grades of the same polymer, raise the pressure slightly for higher molecular weight or higher filler content, and lower it for easier-flow grades. The per-material notes that follow explain the behavior behind each band so you can reason about adjustments instead of guessing.

Material Process Temp (°C) Preblow (bar) Final Blow (bar) Hold Time (s) Mold Temp (°C) Typical Defect Linkage
PET 260–285 8–16 25–40 1.5–3.0 10–25 Low orientation if preblow weak; haze if over-pressured
PCTG 255–280 8–15 24–38 2.0–3.5 20–40 Stress marks if cooled too fast
PP (clarified) 220–260 6–12 20–34 2.0–4.0 20–60 White stress marks if pressure ramps too fast
HDPE 200–230 5–10 16–30 2.0–4.0 10–40 Softness; needs good cooling before eject
LDPE / LLDPE 180–220 4–9 14–26 2.0–4.0 10–40 Low rebound; risk of sticking
PS 200–240 6–12 18–30 1.5–3.0 20–50 Brittle; bursts if final blow too high
SAN 210–250 7–13 20–32 2.0–3.5 40–70 Needs warm mold for gloss; sensitive to over-pressure
PC 280–320 10–18 30–45 3.0–6.0 80–120 High dry requirement; stress cracks if over-pressured
ABS 210–250 7–13 22–36 2.5–4.5 50–80 Opaque; tolerant, medium pressure
TPU 190–230 4–9 14–26 3.0–6.0 20–60 Soft elastic; sticking and rebound control needed

PET y PCTG

PET and PCTG are orientation-sensitive. PET must be dried below about 50 ppm moisture before processing, and the preblow establishes the biaxial orientation that gives the bottle its strength and clarity. A weak preblow leaves the material un-oriented and cloudy; a correct preblow followed by a 25–40 bar final blow gives a clear, strong bottle. PCTG is less moisture-sensitive than PET but still benefits from a controlled ramp; over-pressure on a fast-cooling cavity produces stress whitening rather than crisp detail.

PP

PP is crystallizable and temperature-sensitive. Clarified PP for transparent bottles needs a warm enough mold to control crystallization, yet too warm a mold causes sag that must be countered by adjusting pressure timing rather than by raising pressure blindly. A gentle pressure ramp reduces the white stress marks common in PP. The window of 6–12 bar preblow and 20–34 bar final blow suits most PP bottles.

PE (HDPE, LDPE, LLDPE)

Polyethylene is soft and has low rebound, so it needs relatively low blow pressure. HDPE suits 16–30 bar final blow; LDPE and LLDPE need even less because they are more flexible and tend to stick to the cavity. Cooling and demolding control matter more than raw pressure for PE. Over-pressuring PE wastes air and can flash at the parting line without improving the bottle.

PS y SAN

PS is intrinsically transparent but brittle. Final blow above the material’s comfort band causes burst or micro-cracks. A gentle, well-timed pressure rise is essential. SAN is similar but more chemical-resistant and glossy; it wants a warmer mold (40–70 °C) for surface gloss and a moderate pressure that does not over-stress the part.

PC

PC has high viscosity and demands high drying (below about 50 ppm) plus high process temperature (280–320 °C) and a warm mold (80–120 °C) to avoid stress. Blow pressure is among the highest of the common materials, 30–45 bar final, but the pressure must rise smoothly to avoid internal stress cracking. PC bottles are usually for medical or reusable drinkware where dimensional stability is critical.

ABS

El ABS es opaco, resistente y tolerante. Basta una presión media (22–36 bar final). Se elige para frascos cosméticos y de cuidado personal donde el color y el acabado superficial importan más que la claridad. No se requiere un secado especial más allá del secado normal, y el molde puede operar caliente para una buena superficie.

TPU

El TPU es blando y elástico. Necesita baja presión (14–26 bar final) y un desmoldeo cuidadoso porque la memoria elástica puede causar adherencia y rebote. Un mantenimiento y enfriamiento más largos antes de la expulsión reducen la deformación. Las botellas de TPU aparecen en aplicaciones médicas especializadas y cosméticas de tacto suave.

Corrección de presión según la forma de la botella y el espesor de pared

Una receta de presión que funciona para una botella redonda de 100 ml puede fallar en una botella asimétrica de 750 ml con asa. La tabla siguiente ofrece reglas de corrección que se aplican además de la ventana base del material.

Bottle Type Preblow Correction Final Blow Correction Timing Note
Thin wall (≤ 0.4 mm) Slightly higher to avoid early contact High, for full cavity contact Shorten high-pressure dwell to limit thinning
Thick wall (≥ 1.2 mm) Lower and later Extend dwell and hold Longer hold for complete freeze
Large volume (> 500 ml) Lower, delayed preblow Extend final dwell Manage cooling, watch cycle time
Small volume (< 50 ml) Higher preblow Moderate final Fast cycle, short dwell
Handle or asymmetric Zone-balanced Higher at fill stage for handle Delay to fill recessed zones
Wide mouth Lower preblow Moderate final Watch neck finish
Narrow neck Moderate Ensure base fills first Confirm base before neck pressure

Metodología de ajuste de presión paso a paso

Use el siguiente flujo de decisión siempre que inicie un material nuevo, un molde nuevo o un nuevo tamaño de botella. El flujo mantiene la presión, la temperatura y el tiempo en el orden correcto.

>
Step Action Set / Adjust Verify
1 Fix material temperature window Barrel and mold temp per material table Melt flows, no degradation
2 Set preblow to form bubble Preblow bar and delay per material Even early expansion, no collapse
3 Set final blow for contact Final blow bar and ramp rate Full cavity contact, detail formed
4 Fine-tune timing Preblow delay, final dwell, exhaust Wall distribution balanced
5 Validate the part Measure wall, volume, burst, top load Within spec; no stress marks
6 Save and reuse Store recipe on SD card Same recipe runs on sister machines

Comience en el extremo inferior de la ventana de soplado final y aumente solo hasta lograr el contacto completo con la cavidad. Cada aumento por encima del mínimo es energía de aire comprimido desperdiciada. Documente los valores aceptados para que la receta pueda recargarse en otra IBM65 o IBM75 sin reajustar desde cero.

Defectos relacionados con la presión: referencia rápida de síntomas y ajustes

La tabla siguiente relaciona los defectos de soplado comunes con la dirección de ajuste relacionada con la presión. Trátela como una tarjeta de primera respuesta; confirme siempre con comprobaciones de temperatura y tiempo.

# Symptom Likely Pressure Cause Adjustment Direction
1Poor mold contact / incomplete formingFinal blow too low or delayedRaise final blow; check preblow timing
2Thin wall in shoulder or sidePreblow too early/strong, uneven parisonLower or delay preblow; adjust parison temp
3Thick wall / material pooling at basePreblow too late, final too lowAdvance preblow; raise final blow
4Bottle burst during cycleFinal blow too high or ramp too steepLower final blow; soften ramp
5White stress marks (PP/PE)Pressure ramp too fast, cold materialReduce pressure rate; raise temp
6Flash at parting lineFinal blow exceeds clamping forceLower final blow; verify clamping force
7Neck or finish deformationLocal over-pressure at neckReduce blow at neck; check mold temp
8Unstable base / rockingPreblow timing wrong, base not setAdjust preblow timing; lower final slightly
9Poor detail / embossing unclearFinal blow too low or dwell shortRaise final blow; extend dwell
10Internal stress cracking (PC/PS)Over-pressure, fast coolingLower pressure; raise mold temp; anneal
11Ovality / distortion after ejectPressure-cooling imbalanceBalance pressure with cooling time
12Weld line at handleInsufficient fill-stage pressureRaise final at handle stage; adjust parison
13Surface haze from over-pressureFinal blow too high for materialReduce final blow
14Short shot / incomplete fillAir volume or final blow insufficientRaise final blow; check air supply volume
15Pinch-off too thin / leakClamping and pressure mismatchVerify clamping; tune pressure
16Residual pressure trapExhaust timing too lateAdvance exhaust; check valve

Errores comunes en el ajuste de presión

Incluso los operadores experimentados repiten algunos errores que el método anterior está diseñado para prevenir. Reconocerlos acorta el tiempo de ajuste.

  • Ajustar la presión antes que la temperatura: con una temperatura de cilindro o molde incorrecta, cualquier valor de presión carece de sentido. Corrija primero la temperatura.
  • Perseguir un defecto con más presión: un hombro delgado rara vez se corrige aumentando el soplado final; se corrige con el peso del parisón o el tiempo de pre-soplado. Más presión solo traslada el problema a otro lugar.
  • Usar una sola receta entre materiales: PET y PP no son intercambiables; la receta debe cambiar con el grado de resina.
  • Ignorar la velocidad de rampa: el valor máximo importa menos que la rapidez con que se alcanza. Una rampa suave previene explosiones y marcas de tensión.
  • No guardar la receta: una receta verificada en la tarjeta SD es conocimiento perdido si no se almacena y etiqueta por material y botella.
  • Sobre-presurización por margen de seguridad: un margen de presión del 20% por encima del mínimo rara vez ayuda y siempre desperdicia aire y desgasta el molde.

Sistema neumático y eficiencia energética

Compressed air is one of the largest hidden costs in blow molding. Aibim machines use PREFILL technology and a variable displacement pump pressurizing system in the hydraulic circuit, and a staged high-low pressure air system for the blow function. The energy-saving design reduces consumption by a minimum of 35% compared with conventional hydraulic lines.

Air quality matters. For food, pharmaceutical, and cosmetic bottles the compressed air should be oil-free and dried to a clean class consistent with ISO 8573-1 concepts (oil, water, and particle limits). Contaminated air leaves odors or particles in the bottle and can foul valves. A staged supply separates the low-pressure preblow line from the high-pressure final-blow line so the compressor does not run everything at maximum pressure.

Air recovery, where practical, captures vented blow air or recovers expansion energy, lowering the effective energy per bottle. Even without full recovery, right-sizing the receiver, stabilizing line pressure, and only using the minimum final blow needed already cut air cost substantially. The table below compares energy and air indices using a baseline of 100 index points.

Configuration Air Energy Index Relative Cost vs Baseline
Conventional fixed pump, single pressure135High1.35× baseline
Staged high-low air, no recovery110Medium1.10× baseline
Aibim PREFILL + variable pump + staged air65Low0.65× baseline (35% saved)
Above with air recovery add-on52Low0.52× baseline

Seguridad de los sistemas de aire de alta presión

Las presiones de soplado final alcanzan 25–45 bar, y los sistemas de aire comprimido conllevan un peligro real. Las máquinas Aibim están certificadas CE e incluyen una cortina de luz para la seguridad personal y un sensor láser digital de larga distancia en la estación de desmoldeo para la seguridad del molde. Las reglas de seguridad para el circuito neumático incluyen:

  • Nunca abra una línea presurizada; despresurice y bloquee antes del mantenimiento.
  • Instale y pruebe las válvulas de alivio de presión en los receptores y en el circuito de alta presión.
  • Proteja la estación de soplado contra fragmentos de explosión; la cortina de luz detiene el ciclo si se abre la protección.
  • Inspeccione mangueras, válvulas y accesorios según un programa; reemplácelos según el plan de mantenimiento.
  • Capacite a los operadores sobre la parada de emergencia y el significado de las alarmas de presión.

Métodos de verificación de calidad

Una receta de presión solo es tan buena como la verificación que la respalda. Para cada receta nueva o cambio de material, realice estas comprobaciones:

  • Espesor de pared por zona: mida la base, el cuerpo, el hombro y el cuello con un calibrador de espesores; confirme que la distribución coincide con el diseño.
  • Volumen: llene para confirmar que la botella cumple la capacidad declarada.
  • Carga superior: aplique carga vertical para confirmar la resistencia al apilamiento.
  • Presión de estallido: presurice hasta la falla para confirmar un margen seguro por encima de la presión de llenado.
  • Apariencia: verifique marcas de tensión, turbidez, rebabas y claridad de detalles.
  • Muestreo de la primera pieza y por lotes: califique completamente la primera pieza y luego muestree a intervalos establecidos durante la producción.

Perfil relativo de costo y energía

El costo de producir una botella está dominado por el material, la energía y el desperdicio. La tabla siguiente clasifica los niveles típicos de costo y energía por material en las líneas Aibim IBM. Las clasificaciones usan bandas de Bajo, Medio, Alto, Muy Alto y Premium con puntos de índice referenciados a una línea base de 100.

Material Material Cost Band Energy Index Air Cost Band Process Difficulty
HDPE / LDPELow90LowLow
PPLow95LowMedium
PSMedium100MediumMedium
ABSMedium105MediumLow
SANMedium108MediumMedium
PETMedium110MediumMedium
PCTGHigh112MediumHigh
TPUHigh115HighHigh
PCVery High130HighVery High

El índice de energía es relativo a una línea base de 100 puntos para una botella estándar de PP en una IBM65; el PC es más alto por el secado y la demanda de molde caliente. Ninguna de estas cifras son precios de compra; describen solo el costo de operación relativo.

Máquinas de moldeo por inyección y soplado Aibim

Aibim construye tres series IBM principales, cada una con un sistema neumático controlado para el pre-soplado y el soplado final. Los rangos de especificación siguientes son ventanas de ingeniería típicas; confirme las cifras exactas con la hoja de datos de fábrica para su molde y material.

Máquina de moldeo por inyección y soplado IBM75

Parameter Typical Range
ModelIBM75
Injection screw diameter (mm)45
Shot size (g)80–150
Clamping force (kN)750
Container volume (ml)50–1000
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–16 + 20–40
Installed power (kW)25–33
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)10–16

Máquina de moldeo por inyección y soplado IBM65

Parameter Typical Range
ModelIBM65
Injection screw diameter (mm)40
Shot size (g)60–110
Clamping force (kN)650
Container volume (ml)10–500
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–16 + 20–40
Installed power (kW)18–25
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)9–14

Máquina de moldeo por inyección y soplado IBM55 híbrida eléctrica

Parameter Typical Range
ModelIBM55 Hybrid Electric
Injection screw diameter (mm)35
Shot size (g)40–80
Clamping force (kN)550
Container volume (ml)3–250
Stations3 (injection, blow, eject)
Air config (preblow + final blow, bar)6–14 + 18–36
Installed power (kW)12–18 (hybrid, lower draw)
Air consumptionStaged high-low; tuned per recipe
Cycle time (s)8–13

All three series share the PREFILL hydraulic technology and variable displacement pump pressurizing system, the SD card parameter storage for cross-machine recipe reuse, and the single-crossbeam double-pole clamping framework that enlarges mold setting space. The IBM55 hybrid adds electric servo motion for lower energy draw on small containers.

Industrias de aplicación e idoneidad de materiales

Las máquinas Aibim IBM sirven a las industrias farmacéutica, alimentaria, de bebidas y cosmética. La receta de presión sigue al contenido:

  • Farmacéutica: las botellas de líquido oral, gotas oftálmicas y diagnóstico en PE, PP, PS y PC necesitan piezas limpias y libres de tensión; las rampas suaves de baja presión protegen las superficies en contacto con el fármaco.
  • Alimentos: las botellas de salsa, miel y condimentos en PP y HDPE necesitan cuellos seguros; presión ajustada para la integridad del sellado.
  • Bebidas: las botellas de agua y bebidas funcionales en PET y PCTG necesitan orientación para lograr claridad y resistencia.
  • Cosmética: los frascos de crema en ABS y SAN, los tubos blandos en TPU y los frascos transparentes en PET o PCTG necesitan brillo superficial y detalle; presión ajustada para la calidad del acabado.

Los materiales procesables en toda la gama Aibim son PE (HDPE, LDPE, LLDPE), PP, PS, ABS, SAN, TPU, PC y PCTG.

Guía de selección: de requisito a modelo

Use esta tabla para asignar un requisito a una máquina y a una configuración de aire. Los rangos son orientativos; la selección final depende de la cavitación del molde y del objetivo de producción.

Material Container Volume Wall / Output Recommended Model Air Config
PET / PCTG100–1000 mlMedium, high clarityIBM758–16 + 25–40 bar
PP / HDPE50–500 mlMedium, food gradeIBM656–12 + 20–34 bar
PS / SAN10–250 mlThin, glossyIBM55 Hybrid6–13 + 18–32 bar
PC50–500 mlThick, medicalIBM7510–18 + 30–45 bar
ABS10–500 mlMedium, opaqueIBM657–13 + 22–36 bar
TPU3–250 mlSoft, elasticIBM55 Hybrid4–9 + 14–26 bar
Small pharma3–100 mlHigh volumeIBM55 Hybrid6–14 + 18–36 bar

Servicio y soporte

Aibim, as a Wanplas factory, applies the Wanplas group service commitments. Before shipment each machine is test-run and inspected with the customer, CE certified with light curtain and laser sensor safety. Our engineers perform on-site installation and commissioning, and train your operators on pressure tuning and recipe storage.

The Wanplas shared policy provides USD 500 free parts per year and free replacement of damaged parts within the warranty period. Because recipes are stored on an SD card, a verified pressure setting can be carried to a second machine, which makes process transfer and capacity expansion straightforward. We also offer remote operation support, open our factory for customer visits, and guarantee transportation, production capacity, and quality standards.

Preguntas frecuentes

¿Cuál es la diferencia entre la presión de pre-soplado y la presión de soplado final?

El pre-soplado es la etapa de baja presión que inicia la expansión y establece la distribución de la pared; el soplado final es la etapa de alta presión que completa el contacto con la cavidad y forma el detalle. Ajustar primero el pre-soplado da control sobre el espesor, y luego el soplado final asegura la forma.

¿Cómo afecta el material a la presión de soplado en el moldeo por inyección y soplado?

Cada material tiene una viscosidad y una velocidad de congelación diferentes. El PE blando necesita baja presión; el PC rígido necesita alta presión y un molde caliente; el PS frágil necesita una rampa suave. La tabla de materiales de esta guía ofrece la ventana para cada uno.

¿Puedo usar la misma presión de soplado para PET y PP?

No. El PET requiere un pre-soplado que desarrolle orientación y un soplado final de 25–40 bar, mientras que el PP necesita una rampa más suave y una temperatura de molde que controle la cristalización. Usar una receta de PET en PP causa marcas de tensión; usar una receta de PP en PET da una orientación deficiente y turbidez.

¿Por qué mi botella revienta incluso a presión moderada?

La explosión suele deberse a una rampa de presión demasiado pronunciada, material frío o una pared local delgada por un tiempo de pre-soplado incorrecto. Baje el soplado final o suavice la rampa, aumente ligeramente la temperatura y compruebe el retardo del pre-soplado antes de aumentar la presión.

¿Cómo ajusto la presión de soplado para un nuevo diseño de botella?

Siga el método de seis pasos: ajuste primero la temperatura, ajuste el pre-soplado para la forma de la burbuja, ajuste el soplado final para el contacto, recorte el tiempo, valide la pared y la explosión, y luego guarde en la tarjeta SD. Comience en el extremo inferior de la ventana de soplado final y aumente solo hasta lograr el contacto completo.

¿Una presión de soplado más alta significa mejor calidad de botella?

No. La presión por encima del mínimo necesario para el contacto solo desperdicia aire, aumenta el desgaste del molde y puede causar tensión, explosión y turbidez. El objetivo es la presión más baja que proporcione un contacto completo y uniforme con la cavidad.

¿Cómo ahorra energía el sistema neumático de Aibim?

Aibim utiliza tecnología PREFILL y una bomba de desplazamiento variable en el circuito hidráulico, más un sistema de aire escalonado alto-bajo para el soplado. Esta combinación reduce el consumo de energía en un mínimo del 35% frente a las líneas hidráulicas convencionales, y el aire escalonado evita operar todo a la presión máxima.

¿Qué calidad de aire comprimido se requiere para el soplado?

Para botellas de alimentos, farmacéuticas y cosméticas, el aire debe estar libre de aceite y secado a una clase de limpieza alineada con los conceptos de ISO 8573-1. El aire limpio protege la seguridad del producto y mantiene las válvulas libres de acumulación de aceite que alteraría la estabilidad de la presión.

Conclusión

Blow pressure is not one number but a two-stage system of preblow and final blow, shaped by material, temperature, timing, and bottle geometry. The material table, shape-correction rules, tuning flow, and defect card in this guide give you a repeatable method to find the minimum pressure that delivers full cavity contact and a sound bottle. Aibim, a Wanplas factory, builds IBM75, IBM65, and IBM55 Hybrid machines with PREFILL technology, staged air, and SD-card recipe storage that make this method easy to apply and transfer across lines.

If you are qualifying a new material or bottle, send us your material grade and bottle drawing. We will prepare a material-specific pressure process package and a machine configuration suggestion, and we welcome you to send samples for trial molding and to visit our factory for machine inspection and test runs. Our team will help you lock in a verified, energy-efficient pressure recipe before you scale production.